Home Network Community > Wi-Fi Routers > All setting were reset to factory default after unplugging my Archer C5400 v2.0
< Wi-Fi Routers

All setting were reset to factory default after unplugging my Archer C5400 v2.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

All setting were reset to factory default after unplugging my Archer C5400 v2.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
18 Reply
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2017-09-01 01:04:51
i am use malaysia version also facing this problem
  0  
  0  
#12
Options
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2017-11-25 07:11:37
I am in San Francisco and have the Archer C5400 v2. Same thing happened and the USA beta version fixed it. Support will be able to fork it over. I purposely tripped my breakers at home and Wireless came back after my Arris Cable Modem synced with my ISP.

Archer C5400(US)_V2_20170801_beta.bin
  0  
  0  
#13
Options
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2017-12-29 14:41:46
I am from India and i have the same problem with my router but only with my date and time settings.
Every time there is a power outage the router date and time resets to factory default and it will not connect to the broadband till the date and time is set right.



File:
TP-Link.jpgDownload
  0  
  0  
#14
Options
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2018-02-05 18:57:51
i have same problem here with my Archer C5400 v2
  0  
  0  
#15
Options
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2018-02-07 07:38:24

phonex wrote

i have same problem here with my Archer C5400 v2


Did you update to the latest firmware?

My biggest issue with this device is that it keeps dropping the connection from the ISP. If I connect my laptop directly to the modem, the connection is solid and never drops.
The tplink would connect fine but from time to time it would lose the connection and can't obtain a wan address from the modem for a while. Again, if I connect the laptop directly to the modem, I get an IP address right away so i don't think the issue is with the modem / ISP but with the tplink. Beside that, weak signals, wifi would drop from time to time as well. Spent a lot of money and was hoping for something solid but I'm loosing patience with this device and might end up replacing it
  0  
  0  
#16
Options
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2018-02-07 11:57:27
sometime my device tp-link was also original. i have to configu it. (AC1750)
  0  
  0  
#17
Options
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2018-06-07 04:20:10
This happens on my C3150v2 as well. Everytime there's a power surge or its accidentally unplugged it goes back to its factory settings
  0  
  0  
#18
Options
Re:All setting were reset to factory default after unplugging my Archer C5400 v2.0
2018-06-12 23:27:17
Message to 'gowdac' above.

I too had this issue but found I needed to change the NTP (Network Time Protocol) server settings.

Advanced tab > System Tools > Time Settings

The 'Get automatically from the Internet' would not connect to the default NTP Server settings. When I changed the time manually the router would not keep the date and time at reboot.

I looked up NTP Server IP address on the Internet for my country (UK). Now when I click the Obtain button. Save. Reboot router. it works.

Hope that works for you.
  0  
  0  
#19
Options
12
Related Articles
reset (factory settings)
920 0
default wifi password after factory reset (not admin)
198786 44
Factory reset
1248 0
Factory reset
862 2
 reset PA8010P to factory default
4526 0
Factory reset M5
2819 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.