Home Network Community > Wi-Fi Routers > WDS Bridge stops working after 12 hours
< Wi-Fi Routers

WDS Bridge stops working after 12 hours

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

WDS Bridge stops working after 12 hours

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
WDS Bridge stops working after 12 hours
WDS Bridge stops working after 12 hours
2015-01-18 23:32:37
Region : Brazil

Model : TL-WR941ND

Hardware Version : V3

Firmware Version : Last one from the website

ISP : Virtua Net

Hello,

I configured my TL-WR941ND v3.5 as WDS, and it works fine when I finish configuring it.

However, after 12 hours or so, it stops working. Some devices cannot connect to it and others can, but can't access the internet.

My ISP provider has a dynamic IP, and I don't know if that can interfere with the configuration.

The main router is also TP-Link, but its the TL-WR740N.

Please help me figure it out.

Thank you!
  0      
 
  0      
 
#1
Options
10 Reply
Re:WDS Bridge stops working after 12 hours
2015-01-19 14:17:58
When you cannot access internet with the WDS one, can you still access internet with the main one, WR740?
Change a channel on WR740 like 1, 6 or 11 and reconfigure WR941.
  0  
  0  
#2
Options
Re:WDS Bridge stops working after 12 hours
2015-01-19 18:11:51
Yes, I can access the Internet on the main router.
Also, the WiFi is still up on the 941, but I cannot join it.

I will try changing the channel, but just to be sure, I should change it on both right?
  1  
  1  
#3
Options
Re:WDS Bridge stops working after 12 hours
2015-01-20 09:20:54
Yup, channel in WDS one should be the same as the main one.
  1  
  1  
#4
Options
Re:WDS Bridge stops working after 12 hours
2015-03-19 20:01:31

Mavis wrote

Yup, channel in WDS one should be the same as the main one.
Doesn't work. I tried changing channels 13 or 11 and neither work in the long run. After about 12 hours the wds bridge the devices connected to it cannot access the internet. I have to restart the wds bridge to get it work again. Am frustrated.
  0  
  0  
#5
Options
Re:WDS Bridge stops working after 12 hours
2015-03-31 15:08:05
A rather similar problem over here, only in my case, my WR740N does WDS. It works for a few minutes, then just stops (I have to restart it to get it working again).
  1  
  1  
#6
Options
Re:WDS Bridge stops working after 12 hours
2015-04-01 00:59:35
WDS mode isn't very stable and needs strong wireless signal without interferences.
  0  
  0  
#7
Options
Re:WDS Bridge stops working after 12 hours
2015-04-01 19:58:33

jimasek wrote

WDS mode isn't very stable and needs strong wireless signal without interferences.

Not really an excuse for not implementing a recovery mechanism (if rebooting can fix it, then there's got to be a simpler, automatic solution).
  0  
  0  
#8
Options
Re:WDS Bridge stops working after 12 hours
2015-04-02 22:22:43

white_pawn wrote

Not really an excuse for not implementing a recovery mechanism (if rebooting can fix it, then there's got to be a simpler, automatic solution).

Not an excuse, is the truth, or you don't like truth
As you found out reboot fixes the issue, third party solutions have Cron, (scheduling) learn about it in their forums.
  0  
  0  
#9
Options
Re:WDS Bridge stops working after 12 hours
2015-04-03 04:40:57
I know what a cron job is, and setting a device to automatically reboot every two minutes would be pointless, really. Luckily, now I also know that third party solutions don't have this problem (just tried DD-WRT), so no need to reboot. TP-Link routers have had firmware issues for as long as I can remember, and all I can say is I'm done with them.
  0  
  0  
#10
Options
Re:WDS Bridge stops working after 12 hours
2015-04-03 14:13:57

white_pawn wrote

now I also know that third party solutions don't have this problem, so no need to reboot.
TP-Link routers have had firmware issues for as long as I can remember, and all I can say is I'm done with them.

And if you allready know, as you post, why bother buying other brands, 2X or 3X times more expensive
Enable Cron, it will be a good idea, cause the crowded 2.4 Ghz. band will always give you issues, not in 2 minutes, but after one or two weeks it might, 4am it's a good time
  1  
  1  
#11
Options

Information

Helpful: 0

Views: 3695

Replies: 10

Related Articles
 WDS bridge stops working
1071 0
Administration interface stops working after a few hours
2539 1
 Archer C6 WDS bridge stops working after few days
2534 2
 WDS bridge not working
6210 0
 WDS Bridge getting disconnected after approx 24 hours
732 0
WDS bridge AX20 <-> WD1043ND
3060 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.