Home Network Community > DSL Modem Routers > My (XX230v) Need Low Level Flashing / Firmwaring
< DSL Modem Routers

My (XX230v) Need Low Level Flashing / Firmwaring

My (XX230v) Need Low Level Flashing / Firmwaring

My (XX230v) Need Low Level Flashing / Firmwaring
My (XX230v) Need Low Level Flashing / Firmwaring
a week ago
Tags: #Firmware Update #Recovery
Model: XX230v  
Hardware Version: V1
Firmware Version: Ver 1.0 (ES)

Greeting to all..

i have "AX1800 Dual Band Wi-Fi 6 GPON" (XX230v-ES) no led / very silent seem softwarely died..

i prepare all tools ...just need a firmware

i already open cover and connect (RX TX GND) pins to USB TTL (FTDI)


also using software call (teraterm-4.108 and Hyper Terminal) using speed 115200

 i connect and open connection
then press reset + Power ON

the Text show in Terminal Text as

"Press X"   
then i press X , new text shows as:
"CCCCCCCCCCCCCCCCCCCCCCCCC"

 

 

 

then stopped and device goes silent mode

then i think when "CCC" comes ... the device may need send file
i try all file Transfer protocol by (teraterm / Hyper Terminal)
seem ModemX File Transfer is Responded but
when is reach like 127 KB or 128 KB the transfer is Stop
i think the device only need 128 KB only size
but in Device website the Size of Files is in xx MB
so i think its need some primary firmware update first
i desperately need that file... i didn't find it any where
 

 

 





 

 

  0      
 
  0      
 
#1
Options
3 Reply
Re:My (XX230v) Need Low Level Flashing / Firmwaring
a week ago

  @MohKirkuk 

 

Hi, thanks for posting question here.

As XX230v is a customized model by some ISPs, I am afraid that we have no further solution towards your problem.

Best regards.

 

 

 

Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode.
  0  
  0  
#2
Options
Re:My (XX230v) Need Low Level Flashing / Firmwaring
a week ago - last edited a week ago

  @Marvin_S 

 

thanks for replay .... but

 

the isp only seller...they just buy these router from tp-link and buy to user becouse tp-link dont sell these pon router directly to user.

 

contacting with isp about software will not answered ...or they forward to here becouse firmwaring is tp-link job.

 

 

so i need the source or factory base primal fireware as router seem likly zero software as they in shape they manfacture in tp-link factor and need the first firmware

 

u-boot.bin

or

tclinux.bin

or

tcboot.bin

 

something like that

 

  0  
  0  
#3
Options
Re:My (XX230v) Need Low Level Flashing / Firmwaring
a week ago

  @Marvin_S 

@MohKirkuk 

 

here more info and more digging it

 

AX1800 Dual Band Wi-Fi 6 GPON Router

XX230v

https://service-provider.tp-link.com/gpon/xx230v/

Serial Terminal Connection

 

 

 

--------------------

 

Serial Terminal Output after malfunction

 

Press X

CCCCCCCCCCCCCCCCCCCCCC

 

 

----------------

 

Serial Terminal Output before malfunction

 

Press X

CCCCCCCCCCCCCCCCCC

EN7523DRAMC V0.2

dram_type = 5, speed = 1866

Final Impdance Cal Result: OCDP:0x17, OCDN:0x1e, ODTP:0xa, ODTN:0xa

DDR1866 PLL setting init

[Dramc] PCDDR3 AC Timing update 

Fire MRW command...

ModeReg.2, value.0x20 done

Fire MRW command...

ModeReg.3, value.0x0 done

Fire MRW command...

ModeReg.1, value.0x6 done

Fire MRW command...

ModeReg.0, value.0x1114 done

Fire MRW command...

ModeReg.1, value.0x86 done

Fire MRW command...

ModeReg.1, value.0x6 done

Calculate size.

DRAM size=256MB

 

Press x to update firmware

CCCCCCCCCCCCCCCCCC

 

 

U-Boot 2014.04-rc1 (Oct 23 2023 - 06:47:22)

DRAM: 240 MiB

EN7529CT

Now running in RAM - U-Boot at: 8edff000

spi_nand_probe: mfr_id=0xc8, dev_id=0x1

Using Flash ECC.

Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_F50L1G41LB, Flash Size=0x8000000

bmt pool size: 81 

BMT & BBT Init Success 

In: serial

Out: serial

Err: serial

CPU0: found redistributor 0 region 0:8ee3d988

Net: ecnt_eth

Uip activated

.

.

.

.

ECNT>

-------------

ECNT> version

U-Boot 2014.04-rc1 (Oct 23 2023 - 06:47:22)

arm-buildroot-linux-gnueabi-gcc (Buildroot 2015.08.1-gd814875) 4.9.3

GNU ld (GNU Binutils) 2.24

 

----------------

ECNT> coninfo

List of available devices:

serial 80000003 SIO stdin stdout stderr 

ecnt_uart 00000003 .IO

 

----------------------

ECNT> bdinfo

arch_number = 0x00001D63

boot_params = 0x80000100

DRAM bank = 0x00000000

-> start = 0x80000000

-> size = 0x0F000000

eth0name = ecnt_eth

ethaddr = []

current eth = ecnt_eth

ip_addr = 192.168.1.1

baudrate = 115200 bps

TLB addr = 0x8EFF0000

relocaddr = 0x8EDFF000

reloc off = 0x0CFFF000

irq_sp = 0x8CDFAF40

sp start = 0x8CDF8F30

 

--------------------

ECNT> base

Base Address: 0x00000000

 

--------------------

ECNT> showvar

HUSH_VERSION=0.01

 

------------

ECNT> printenv

 

arch=arm

baudrate=115200

board=en7523_evb

board_name=en7523_evb

bootcmd=flash tpimg;bootm 81800200

bootdelay=1

bootfile=tclinux.bin

console=ttyS0,115200n8 earlycon

country_code=ff

cpu=armv7

dsl_gpio=0b

ethact=ecnt_eth

ethaddr=[]

ether_gpio=0c

fdt_high=0xac000000

fileaddr=81000000

filesize=1a6636a

internet_gpio=02

invaild_env=no

ipaddr=192.168.1.1

kernel_filename=tclinux.bin

loadaddr=0x81800000

multi_upgrade_gpio=0b020400000000000000000000000000

onu_type=2

password=[]

power_gpio=1515

product_name=xPON ONU

qdma_init=33

root=/dev/mtdblock8 ro

sdram_conf=0x00108893

serdes_sel=0

serverip=192.168.1.100

snmp_sysobjid=1.2.3.4.5

soc=en7523

stderr=serial

stdin=serial

stdout=serial

uboot_filename=tcboot.bin

username=telecomadmin

vendor=ecnt

vendor_name=ECONET Technologies Corp.

verify=0

Environment size: 893/16380 bytes

 

---------------------

ECNT> iminfo

## Checking Image at 81000000 ...

Unknown image format!

 

-------------------

ECNT> imginfo

mtd parts is NULL

mtd parts is NULL

get_tclinux_img_version, read trx magic(0x32524448) error.

Read first tclinux.bin from flash 0x0 error.

get_tclinux_img_version, read trx magic(0x32524448) error.

Read second tclinux.bin from flash 0x0 error.

imginfo - imginfo - Show tclinux.bin version command

 

---------------------------

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 86

Replies: 3

Tags

Firmware Update
Recovery
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.