Home Network Community > Deco > Deco X55 gets no internet connection with xFi Gateway
< Deco

Deco X55 gets no internet connection with xFi Gateway

Deco X55 gets no internet connection with xFi Gateway

Deco X55 gets no internet connection with xFi Gateway
Deco X55 gets no internet connection with xFi Gateway
2 weeks ago
Tags: #Network Connectivity #Access Point Mode
Model: Deco X55  
Hardware Version:
Firmware Version: 1.5.5

I'm struggling to setup our Deco X55 mesh network (1 main, 2 nodes). 

 

I have an xFi Gateway that I switched to enable Bridge Mode (turning off its Wi-Fi capabilities). Based on what I understood from this forum and other online resources, I should enable AP mode on the Deco, which should effectively make my Deco the Wi-Fi + Mesh network for the whole home. However, the Deco will not recognize the internet connection physically connected by ethernet cable. Basically, I end up with NO internet at all. 

 

I reversed this and disabled Bridge Mode on the xFi Gateway but kept AP mode on. Now ALL devices are ONLY connected to the main Deco and the nodes have become useless - no devices connect to it. Also, internet speeds are back in 2005 (very slow) and I don't know why this is not working....I am thinking of going back to wi-fi mode again as at least the speeds were decent. 

 

Before all these changes, I had Deco in Wi-Fi Mode and the issue there (as many report online) is that some devices get confused by running 2 networks (with the same SSID but different passwords) - I was trying to solve this and create only a single network that is mesh but fail to do so

 

Appreciate any help! 

  1      
 
  1      
 
#1
Options
4 Reply
Re:Deco X55 gets no internet connection with xFi Gateway
2 weeks ago

  @farmboy456 

Hi, welcome to the community.

May I know the model number of your Xfinity Gateway?

-I think it might depend on how the "Bridge Mode" on the Xfi gateway works.

Usually, when the gateway router is set to bridge mode, it no longer performs as a DHCP router so Deco needs to work in "Wireless router mode".

Sometimes, the ISP gateway router doesn't have "Bridge mode". We will suggest users disable their WiFi to avoid the WiFi overlapping. However, the ISP gateway still has the DHCP function. In this way, "Access Point" mode is recommended.

 

For your case, it is like the first one and when you set Xfi Gateway to "Bridge mode", Deco needs to be kept in router mode.

Thank you very much and best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:Deco X55 gets no internet connection with xFi Gateway
2 weeks ago

  @David-TP 

Thanks for your reply! 

 

I believe you are correct in your assessment and the first scenario is what's happening. The xFi Gateway model name is the "XB7-T". Bridge mode is currently DISABLED on the Gateway Modem and Deco X55 router is in Access Point mode with Smart DHCP enabled. It appears that the various connected devices have started to connect to the closest Deco node. When I first posed my question, nearly all devices were connected to the Deco device that is physically connected by ethernet to the Modem. Internet speeds and stability seems adequate. 

 

So if I follow you correctly, you recommend that if I ENABLE bridge mode, I need to keep the Deco in Wifi Mode? What would be the advantage of these settings compared to the current settings?

  0  
  0  
#3
Options
Re:Deco X55 gets no internet connection with xFi Gateway
2 weeks ago

  @farmboy456 

Hi, Thanks for the feedback.

I checked the FAQ of xFi Gateway-"XB7-T", it mentioned that:

https://www.xfinity.com/support/articles/wireless-gateway-enable-disable-bridge-mode

To do this on our network, you'll have to enable the Bridge Mode feature on your wireless gateway, which turns off its routing capabilities while leaving the modem capabilities on. Then, you may connect and use your own router.

Note: Any ethernet port can be used but only one device can be connected to the gateway while in Bridge Mode.

 

-So, yes, you need to keep Deco in "Wireless router"mode when Bridge mode is enabled.

For the difference of Deco in AP mode and router mode, you could refer to 

What’s the difference between Access Point mode and Router mode on the Deco?

 

The decision might depend on whether you prefer using Deco or the X87 work as the DHCP router. If there are some advanced features that X87 has but Deco didn't, the current setup would be recommened. While if you plan to make full use of Deco advanced featues, Deco will be recommened to work as the DHCP router.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
  0  
  0  
#4
Options
Re:Deco X55 gets no internet connection with xFi Gateway
a week ago

  @David-TP Thank you so much for your response and including links. I'm going to research this and test this out. This is very helpful.

 

 

  0  
  0  
#5
Options

Information

Helpful: 1

Views: 134

Replies: 4

Tags

Network Connectivity Access Point Mode
Related Articles
 Deco X55 – “No internet connection”
3159 1
Deco X55 and HP printers
115 0
Deco X55 not using ethernet for backhaul
166 0
Deco X55 & x55 Pro compatibility
281 0
 Deco X55 randomly stops internet connection while staying connected to network
236 0
Deco X55 VoiP
147 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.