Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > Main router can't see IP cams on secondary router. How to configure it?

< Wi-Fi Routers

Main router can't see IP cams on secondary router. How to configure it?

Main router can't see IP cams on secondary router. How to configure it?

Main router can't see IP cams on secondary router. How to configure it?

2024-10-21 13:11:18 - last edited 2024-10-21 18:48:42

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2024-10-21

Main router can't see IP cams on secondary router. How to configure it?

2024-10-21 13:11:18 - last edited 2024-10-21 18:48:42

Model: Archer AX72

Hardware Version: V1

Firmware Version: 1.2.6 Build 20240619 rel.72016(5553)

Hi, sorry if this is nto the right forum, but I need help to setup my network.

What I have now:
Modem (opctic fiber) ---> AX72 (main router)---(ethernet )---> AX53 (secondary router)

On AX72 I have 3 IP cams and 1 NVR to record IP cams videos. AX72 assigns ip range 192.168,.0.x to all, including AX53
On AX 53 I have 3 more IP cams with IP range 192.168.1.x, as it got a 192.168.1.1 IP assigned at setup to avoid conflict with AX72(i guess)

All dynamic IPs.

Problems: The NVR can't find the cams at 192.168.1.x

How do I solve it so all the cams get a 192.168.0.x ip?

Tryed to setup AX54 as mesh satellite, but AX72 didn't found it. Also they must be linked by ethernet cable.

Thanks for any help

BF

0

0

#1

1 Accepted Solution

LV7

2024-10-21 16:21:25 - last edited 2024-10-21 18:48:42

Posts: 7137

Helpful: 5350

Solutions: 1216

Stories: 7

Registered: 2013-10-12

Re:Main router can't see IP cams on secondary router. How to configure it?-Solution

2024-10-21 16:21:25 - last edited 2024-10-21 18:48:42

If you set AX53 in AP mode (Case 1) all IP cams would be ihe same subnet and NVR would see all of them - they would be all in 192.168.0.0/24 subnet.

Depending on your AX53 HW version you can also use as alternative Easymesh with an ethernet backhall - check this thread for details.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Recommended Solution

2

2

#2

2 Reply

LV7

2024-10-21 16:21:25 - last edited 2024-10-21 18:48:42

Posts: 7137

Helpful: 5350

Solutions: 1216

Stories: 7

Registered: 2013-10-12

Re:Main router can't see IP cams on secondary router. How to configure it?-Solution

2024-10-21 16:21:25 - last edited 2024-10-21 18:48:42

If you set AX53 in AP mode (Case 1) all IP cams would be ihe same subnet and NVR would see all of them - they would be all in 192.168.0.0/24 subnet.

Depending on your AX53 HW version you can also use as alternative Easymesh with an ethernet backhall - check this thread for details.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Recommended Solution

2

2

#2

LV1

2024-10-21 18:48:23

Posts: 3

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2024-10-21

Re:Main router can't see IP cams on secondary router. How to configure it?

2024-10-21 18:48:23

@terziyski hi,
Access point solved the "issue".
Thank you very much

0

0

#3