Home Network Community > DSL Modem Routers > Virtual Servers error code 4620 on TP-Link Archer VR1210v
< DSL Modem Routers

Virtual Servers error code 4620 on TP-Link Archer VR1210v

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Virtual Servers error code 4620 on TP-Link Archer VR1210v

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Virtual Servers error code 4620 on TP-Link Archer VR1210v
Virtual Servers error code 4620 on TP-Link Archer VR1210v
2024-07-21 13:05:18
Tags: #Port Forwarding #Web GUI Management
Model: Archer VR1210v  
Hardware Version: V1
Firmware Version: 2.0.0 0.9 v6041.0 Build 221027 Rel.12900n

While I can add virtual servers for other ports (see 443 in the screenshot) I have a problem trying to add port forwarding on port 80 on my VR1210v:

 

 

The port is NOT used since I moved local and remote management on other ports (local was on 80/443 before):

 

 

 

Is there a way to fix this error?

 

  0      
 
  0      
 
#1
Options
6 Reply
Re:Virtual Servers error code 4620 on TP-Link Archer VR1210v
2024-07-21 13:06:34

I can add that local management on port 8080 works and nothing respond on port 80 so it should be free.

  0  
  0  
#2
Options
Re:Virtual Servers error code 4620 on TP-Link Archer VR1210v
2024-07-22 09:34:54

  @brand5 

 

A similar behavior could be observed if the router has its UPnP feature enabled. Disable UPnP and reboot the router, then try to port-forward TCP 80 again.

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#3
Options
Re:Virtual Servers error code 4620 on TP-Link Archer VR1210v
2024-07-22 13:45:04

@terziyski thank you for your answer but sadly UPnP is already disabled.

 

  0  
  0  
#4
Options
Re:Virtual Servers error code 4620 on TP-Link Archer VR1210v
2024-07-22 13:59:40 - last edited 2024-07-22 14:51:09

  @brand5 

 

VR1210v is an ISP provided device and probably a newer FW release could fix this. Unfortunatelly you can obtain a newer FW release only from your ISP (it they have one) or at least ask them for assistance on this issue.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#5
Options
Re:Virtual Servers error code 4620 on TP-Link Archer VR1210v
2024-07-22 14:12:26

  @terziyski mine is ISP provided but I managed to update to the latest version already (cracked admin pass from config backup... it is my work) but even with some knowledge still can't find the problem and have no time to dig into the firmware now.

 

any other suggestion?

  0  
  0  
#6
Options
Re:Virtual Servers error code 4620 on TP-Link Archer VR1210v
2024-07-23 09:35:13

  @brand5 

Hi, I think you could try to back up the current network configuration, and then factory reset the modem once.

After that, before configuring the internet, you could change the default local management port to something other than port 80. Then open port 80 again to see whether the same error pops up again.

Thank you very much and best regards.

▶Deco BE11000/ BE63_V2.6_1.1.7 Ready for Test ▶Deco BE25_V1_1.0.17 Ready for Test! ▶Update Deco BE65 Pro to the Latest 1.1.3 Firmware Now! Try to leave a Message if urgent help is required.
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 601

Replies: 6

Tags

Port Forwarding Web GUI Management
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.