Pppoe show 0.0.0.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Pppoe show 0.0.0.0

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Pppoe show 0.0.0.0
Pppoe show 0.0.0.0
2024-03-23 17:00:56 - last edited 2024-04-08 09:13:13

I have ppoe connection when i try to set this connection in new wifi device it show wan ip address 0.0.0.0

note that i have use this user id and password in other wifi befor but now not use this id at any other wifi only this wifi only 

what we have to do is this problem with wifi or service provider?if wifi problems than how to solve it ? Please guide this 

  0      
  0      
#1
Options
1 Accepted Solution
Re:Pppoe show 0.0.0.0 -Solution
2024-03-25 09:19:44 - last edited 2024-04-08 09:13:13

  @Kaustubh-8 

 

What is the model no., hardware and firmware version of your TP-Link router? and who is your ISP?

 

When you configure PPPoE, except for username and password, please also confirm if your internet requires any Internet VLAN ID to connect internet access.

If your old WiFi router is still available, you could also connect back to your old router and double check all the internet settings for comparison.

If indeed there is no VLAN ID, please disconnect the router, connect a computer to your ISP modem directly and configure PPPoE on the computer to see if it works:

How to set up a PPPoE connection on Windows 8&10

How to configure PPPoE connection on Mac pro

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Pppoe show 0.0.0.0 -Solution
2024-03-25 09:19:44 - last edited 2024-04-08 09:13:13

  @Kaustubh-8 

 

What is the model no., hardware and firmware version of your TP-Link router? and who is your ISP?

 

When you configure PPPoE, except for username and password, please also confirm if your internet requires any Internet VLAN ID to connect internet access.

If your old WiFi router is still available, you could also connect back to your old router and double check all the internet settings for comparison.

If indeed there is no VLAN ID, please disconnect the router, connect a computer to your ISP modem directly and configure PPPoE on the computer to see if it works:

How to set up a PPPoE connection on Windows 8&10

How to configure PPPoE connection on Mac pro

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options