Official Release Deco X50/X55_V1_1.5.5 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
This Article Applied to
Deco X50/X55_V1_1.4.1
Firmware Modifications
1. Support WireGuard VPN Server/Client.
2. Support built-in easy configuration of NordVPN/Surfshark VPN.
Note: In compliance with local regulations, the Third-party VPN feature may be restricted in specific regions.
3. Add client speed limit under clients' detailed setting page.
4. Support Fixing the WAN port under Deco APP>More>Advanced>WAN Port.
5. Add Scene Priority under QOS.
6. Add Client MAC Identification to improve the accuracy of device detection.
7. Add more device icons in the Deco APP.
Download Link
| Deco X50_V1 | Deco X50_V1_1.5.5- updated 2024.8.12 |
| Deco X55_V1 | Deco X55_V1_1.5.5- updated 2024.8.12 |
Note:
1. *According to the user feedback and our further test, this 1.5.1 version does not support reverting to 1.4.1 via downgrade firmware recovery directly.
-Ever since 1.3.0, the firmware bin file has been over 32MB which passes the maximum file size of the HTTP uboot upgrade tool. So if you want to revert to 1.4.1, please refer to the following suggestions:
- Still run a firmware recovery on one of the satellites Deco X50 first.
- Try to upload an older official version, 1.2.2_Build_230301.zip for example,
- Then update to 1.4.1 from 1.2.2 via web UI.
- If this process works for the satellite Deco X50, We could repeat it on the main Deco later.
2. Please make sure the Deco APP is up-to-date.
3. Some features might not be available when there are other models in the Mesh network.
Configuration Procedure for the Newly-added Features
WireGuard VPN Server& Client
NordVPN/Surfshark VPN
-
NordVPN
-
Surfshark
Client Speed Limit
Manual Selection of the WAN Port
Set Scene Priority under QOS
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi David, my responses are below in red. Thanks for taking a look at things.
|
- Copy Link
- Report Inappropriate Content
@David-TP One other thing, the label on my Deco X55 shows it to be hardware v1.6 but the firmware upgrade page in the Web UI shows v1.0. Any reason why that might be?
- Copy Link
- Report Inappropriate Content
Hi, V1.6 is alslo V1. Usually, x.6/x.8 variants are to mark the production place.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP Hi. David. It was cool to test new firmware on x50 v1, but yesterday my DECO stopped working. Yellow light is on. Computer is not detected in Ethernet port (not even physical connection light is on, in all 3 ports). I liked testing X50 ;-). I tried to resurrect according to instructions. But it did not help. Apparently, Ethernet ports are not working.Hi. David. It was cool to test new firmware on x50 v1, but yesterday my DECO stopped working. Yellow light is on. Computer is not detected in Ethernet port (not even physical connection light is on, in all 3 ports). I liked testing X50 ;-). I tried to resurrect according to instructions. But it did not help. Apparently, Ethernet ports are not working.
- Copy Link
- Report Inappropriate Content
Hi, nice to see you again.
Did a factory reset on Deco X50(hold the reset pinhole for 1s only) make any difference?
Please also try to switch to another power socket(or a different power adapter if possible) since I wonder whether it was because the Deco X50 couldn't boot up properly.
I saw there were Deco X20 units under your TP-link email ID. Have you tried to switch Deco X20 as the main Deco, then connect the cable devices to Deco X20 to see whether they can receive internet service?
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
Hi, nice to see you again.
Did a factory reset on Deco X50(hold the reset pinhole for 1s only) make any difference?
Yes. no difference .
Please also try to switch to another power socket(or a different power adapter if possible) since I wonder whether it was because the Deco X50 couldn't boot up properly.
Yes. i try to use x20v4 power adapter
I saw there were Deco X20 units under your TP-link email ID. Have you tried to switch Deco X20 as the main Deco, then connect the cable devices to Deco X20 to see whether they can receive internet service?
yes. in X20v4 connected the internet provider and devices. everything worked
- Copy Link
- Report Inappropriate Content
Hi, Thanks for the fast reply.
In the way, we could make a final attempt to run a firmware recovery on Deco X50 and test whether it could get into firmware recovery mode:
If it could turn solid/flashing green, we could try to upload the 1.2.2 firmware to the management UI
https://www.tp-link.com/en/support/faq/2958/
However, if it couldn't get into firmware recovery mode, or web management page is not accessible, I think you might need to contact the shop retailer to ask for warranty service.
Thank you very much and best regards.
- Copy Link
- Report Inappropriate Content
@David-TP I just got a call from the service center. They said the router can't be repaired. The router is under warranty. Now I don't know what to do. How can I get a new one. Shouldn't the service center issue a new one?
- Copy Link
- Report Inappropriate Content
Hi, Thank you very much for the time and patience.
Have you checked the warranty policy here:
https://www.tp-link.com/ru/support/service-center/
Best regards.
- Copy Link
- Report Inappropriate Content
I was waiting for Wireguard support and saw this thread so was excited!
Is there any reason why this is not coming up automatically with software update via the app or on the webui it says there is no new firmware?
Is this still in beta? Can I safely install this update?
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 37412
Replies: 196
Voters 1
