Official Release Deco X50/X55_V1_1.5.5 Support WireGuard VPN, Client Speed Limit and Fixed WAN Port
This Article Applied to
Deco X50/X55_V1_1.4.1
Firmware Modifications
1. Support WireGuard VPN Server/Client.
2. Support built-in easy configuration of NordVPN/Surfshark VPN.
Note: In compliance with local regulations, the Third-party VPN feature may be restricted in specific regions.
3. Add client speed limit under clients' detailed setting page.
4. Support Fixing the WAN port under Deco APP>More>Advanced>WAN Port.
5. Add Scene Priority under QOS.
6. Add Client MAC Identification to improve the accuracy of device detection.
7. Add more device icons in the Deco APP.
Download Link
| Deco X50_V1 | Deco X50_V1_1.5.5- updated 2024.8.12 |
| Deco X55_V1 | Deco X55_V1_1.5.5- updated 2024.8.12 |
Note:
1. *According to the user feedback and our further test, this 1.5.1 version does not support reverting to 1.4.1 via downgrade firmware recovery directly.
-Ever since 1.3.0, the firmware bin file has been over 32MB which passes the maximum file size of the HTTP uboot upgrade tool. So if you want to revert to 1.4.1, please refer to the following suggestions:
- Still run a firmware recovery on one of the satellites Deco X50 first.
- Try to upload an older official version, 1.2.2_Build_230301.zip for example,
- Then update to 1.4.1 from 1.2.2 via web UI.
- If this process works for the satellite Deco X50, We could repeat it on the main Deco later.
2. Please make sure the Deco APP is up-to-date.
3. Some features might not be available when there are other models in the Mesh network.
Configuration Procedure for the Newly-added Features
WireGuard VPN Server& Client
NordVPN/Surfshark VPN
-
NordVPN
-
Surfshark
Client Speed Limit
Manual Selection of the WAN Port
Set Scene Priority under QOS
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@David-TP I have this version on it. But it doesn't change anything.
- Copy Link
- Report Inappropriate Content
Thanks for the reply and I will ask the engineer again for the update.
Sorry for the inconvenience.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
Deco X50-POE is planned to support similar features but there hasn't been an ETA yet.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi,
I have a 3 deco mesh network connected like below:
Spectrum modem -----> main deco X55 ------> 8 port switch -------- 2 Deco W6000s
I am experiencing frequent "Network device 'br-wan' link is down" disconnects starting at least a couple of months back and at the time I manually updated the X55 I have to the newest firmware manually which was the 1.5.0 firmware because it wouldn't automatically update via the app despite it being the newest on the website. Unfortunately after the update, the disconnects seemed to become more frequent. All of the logs I've captured show the wan connection being down for about 3 seconds total which is enough to knock internet out for all 60 devices on my network. In most cases I didn't see the main deco's light turn red, I would simply notice that the connection was down if I was watching something streaming or I was working and my VPN noticed the loss of connectivity. I also noticed that the 1.5.0 firmware is no longer listed as the newest firmware for the x55 so that is not good also. Is there a way to downgrade the firmware so I can at least try to get it to be useable? Thanks in advance.
Fri May 3 22:21:55 2024 daemon.notice netifd: Network device 'br-wan' link is down
Fri May 3 22:21:58 2024 daemon.notice netifd: Network device 'br-wan' link is up
- Copy Link
- Report Inappropriate Content
Hi, Thanks for the update.
The official 1.5.1 Build 20240417 for Deco X55 was released yesterday. I think you could try to manually install the final official version to see whether it helped with the WAN link error:
https://www.tp-link.com/us/support/download/deco-x55/v1/#Firmware
(V1.6 shared the same firmware download link with V1.0)
Wait for your reply and best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@cypherguy Hello,
Deco X50/X55_V1 share same firmware, I update my Deco X50 with newest 1.5.1 Deco X55 firmware and work well and have no problems with it.
- Copy Link
- Report Inappropriate Content
@David-TP X20v4 router on the same platform as x50/x55? when should we expect an update or beta for it?
- Copy Link
- Report Inappropriate Content
Hi, Deco X20_v4_1.2.0 and Deco X50_V1_1.4.1 are on the same firmware platform.
Understand the Differences Among Deco Firmware Platforms
1.5.0/1.5.1 is one step further.
Best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 2
Views: 34826
Replies: 196
Voters 1
