Home Network Community > Deco > Solid red light on base unit
< Deco

Solid red light on base unit

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Solid red light on base unit

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Solid red light on base unit
Solid red light on base unit
2024-02-01 12:02:32 - last edited 2024-04-04 11:45:29
Model: Deco XE75  
Hardware Version:
Firmware Version:

Suddenly, last night, had this dreaded solid Red light on the base unit. Internet was fine - checked with old router.

 

Tried a few things but ended up having to reset the unit and setup from scratch! This was a bit painful.

 

Is there a way I can save the settings or is there a way to get out of the solid red light?

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:Solid red light on base unit-Solution
2024-04-04 09:35:04 - last edited 2024-04-04 11:45:33

  @wizzard1 if the Deco can't connect to the app then I can't see a way you would be able to reset it remotely. I would suggest a smart plug as a workaround but the lack of internet would probably prevent that from working too.

 

I suspect that your problem will be due to an internet outage from your ISP causing problems with the Deco and its auto-WAN port sensing. Once your ISP modem/router reconnects your Deco probably isn't picking up the new connection for some reason. You would probably need to send the logs to Deco support to figure it out but you can only access them via the web interface so you'd need to hardwire a laptop/computer to the main Deco to extract them.

XE75 V1.0 3-pack / Wired backhaul / Router mode / UK
Recommended Solution
  0  
  0  
#7
Options
Re:Solid red light on base unit-Solution
2024-04-04 10:27:11 - last edited 2024-04-04 11:45:29

  @wizzard1 you'll need to open a browser and go to the IP address for your router, usually 192.168.68.1 for TP-Link products but if not you can open a cmd window in Windows and type "ipconfig" and press enter. Look for the Default Gateway and type that into your browser:

 

 

Then you just need to sign in with your TP-Link account details and go to Advanced > System > System Logs and export a copy from there. The problem however is that the logs are wiped with every reboot so you'll need to export a copy after the next failure.

XE75 V1.0 3-pack / Wired backhaul / Router mode / UK
Recommended Solution
  0  
  0  
#9
Options
10 Reply
Re:Solid red light on base unit
2024-02-01 13:14:06

  @wizzard1 there's an option to make a different Deco unit the mian unit, that would allow you to keep the settings the same and swap your units around. Bit of a pain but it worked for me when I had to RMA my 3-pack of XE75s. Just click the 3 dots on your network map and you should see the option there.

XE75 V1.0 3-pack / Wired backhaul / Router mode / UK
  0  
  0  
#2
Options
Re:Solid red light on base unit
2024-02-01 13:42:12

  @Wrayman 

 

I should have made it clearer - the base unit lost connection and the other 2 stopped functioning as well, so transfer would not be possible.

  0  
  0  
#3
Options
Re:Solid red light on base unit
2024-02-01 13:49:44

  @wizzard1 I see, so when you say it's not functioning you're saying you can't see it in the Deco app at all or it just won't let you set up a new main unit?

 

Either way, when I had a red light on my main unit the only way I could get it to start working again was to connect the ethernet cable from my modem into a different port on the main Deco. Not sure why it worked but it did, that could potentially save some hassle if you get the red light again and enable you to set a new main unit if necessary.

XE75 V1.0 3-pack / Wired backhaul / Router mode / UK
  0  
  0  
#4
Options
Re:Solid red light on base unit
2024-02-01 13:58:30

  @Wrayman 

 

Cannot see it in the app.

 

Next time, I will try swapping the port as you suggest - I hope that time does not come! 

  1  
  1  
#5
Options
Re:Solid red light on base unit
2024-04-04 08:11:51

  @Wrayman 

 

Red light again (twice) last nightangry. Only way was to switch the main Deco off / on. Why does this happen?

 

Also, if I am away, can this be reset remotely please?

  0  
  0  
#6
Options
Re:Solid red light on base unit-Solution
2024-04-04 09:35:04 - last edited 2024-04-04 11:45:33

  @wizzard1 if the Deco can't connect to the app then I can't see a way you would be able to reset it remotely. I would suggest a smart plug as a workaround but the lack of internet would probably prevent that from working too.

 

I suspect that your problem will be due to an internet outage from your ISP causing problems with the Deco and its auto-WAN port sensing. Once your ISP modem/router reconnects your Deco probably isn't picking up the new connection for some reason. You would probably need to send the logs to Deco support to figure it out but you can only access them via the web interface so you'd need to hardwire a laptop/computer to the main Deco to extract them.

XE75 V1.0 3-pack / Wired backhaul / Router mode / UK
Recommended Solution
  0  
  0  
#7
Options
Re:Solid red light on base unit
2024-04-04 10:08:48

  @Wrayman  Many thanks

 

Have my PC connected to the Deco via ethernet. How do I get the logs please?

 

  0  
  0  
#8
Options
Re:Solid red light on base unit-Solution
2024-04-04 10:27:11 - last edited 2024-04-04 11:45:29

  @wizzard1 you'll need to open a browser and go to the IP address for your router, usually 192.168.68.1 for TP-Link products but if not you can open a cmd window in Windows and type "ipconfig" and press enter. Look for the Default Gateway and type that into your browser:

 

 

Then you just need to sign in with your TP-Link account details and go to Advanced > System > System Logs and export a copy from there. The problem however is that the logs are wiped with every reboot so you'll need to export a copy after the next failure.

XE75 V1.0 3-pack / Wired backhaul / Router mode / UK
Recommended Solution
  0  
  0  
#9
Options
Re:Solid red light on base unit
2024-04-04 11:46:18

  @Wrayman 

 

Many thanks. Really helpful

  0  
  0  
#10
Options
Re:Solid red light on base unit
2024-04-04 11:50:42

  @wizzard1 no worries, hope you get it sorted! yes

XE75 V1.0 3-pack / Wired backhaul / Router mode / UK
  0  
  0  
#11
Options

Information

Helpful: 0

Views: 839

Replies: 10

Related Articles
Solid red light
2559 0
 Deco unit light is solid red
2123 0
M5 Solid red light after update
1270 0
 Solid red light
1258 2
 Solid red light, no internet after firmware upgrade
483 1
 Base Unit Speed Test
408 7
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.