Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > AX55 V1 will not go into mesh satellite mode

< Wi-Fi Routers

AX55 V1 will not go into mesh satellite mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

AX55 V1 will not go into mesh satellite mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Jon_Heron

2023-09-02 02:02:49 - last edited 2023-09-04 22:53:06

Posts: 4

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2023-09-02

AX55 V1 will not go into mesh satellite mode

2023-09-02 02:02:49 - last edited 2023-09-04 22:53:06

Model: Archer AX55

Hardware Version: V1

Firmware Version: Archer AX55(CA)_V1_1.2.3 Build 20230603

I just bought an AX73 to use as my main router and wanted to use my existing AX55 as a wireless repeater for it, doh! It doesnt have repeater mode.

I see though I should be able to link to it with mesh satellite mode instead?

When I set the AX55 to "Satellite mode" it just resets to factory defaults every time. I tried reverting the firmware to Archer AX55(CA)_V1_1.2.0 Build 20230314 and had the same result so I updated to the latest firmware again and it was the same, it just resets the router to factory and reboots...

The UI shows the timers and everything looks like it went fine but before its even done the router boots back up to defaults.

Any assistance here would be great!

Cheers,

Jon

1 Accepted Solution

Jon_Heron

LV1

2023-09-04 20:51:10 - last edited 2023-09-04 22:53:06

Posts: 4

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2023-09-02

Re:AX55 V1 will not go into mesh satellite mode-Solution

2023-09-04 20:51:10 - last edited 2023-09-04 22:53:06

@terziyski

Thanks for that!

So they connect after pushing the WPS wifi button on each unit.

Once they are connected you can no longer log into the AX55 which is what the instructions stated.

We had to leave this morning and these are at a second property where we share a starlink with the neibours, will be interesting to see if they connect back up automatically after the power goes out.

Cheers,

Jon

Recommended Solution

5 Reply

terziyski

LV7

2023-09-02 02:20:32

Posts: 7135

Helpful: 5350

Solutions: 1216

Stories: 7

Registered: 2013-10-12

Re:AX55 V1 will not go into mesh satellite mode

2023-09-02 02:20:32

@Jon_Heron

Here's a thread which describes how to connect OneMesh capable router (like AX73) to an EasyMesh capable router (like AX55).

AX55 just needs to be reset to its factory defaults before adding it to the AX73 mesh network.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Jon_Heron

LV1

2023-09-02 03:48:53

Posts: 4

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2023-09-02

Re:AX55 V1 will not go into mesh satellite mode

2023-09-02 03:48:53

@terziyski

Thank you very much!

I tried what was suggested (to the best of my understanding) and still no joy.

I posted a followup there.

Cheers,

Jon

terziyski

LV7

2023-09-02 10:54:47

Posts: 7135

Helpful: 5350

Solutions: 1216

Stories: 7

Registered: 2013-10-12

Re:AX55 V1 will not go into mesh satellite mode

2023-09-02 10:54:47

@Jon_Heron

You mentioned that AX55 is with "CA" FW region, what about AX73 - what's the FW region and FW version ?

Did you try to follow this post and check if you can add AX55 to the AX73 Onemesh network ?

Make sure that you're with the latest FW on both AX55 and AX73.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".

Jon_Heron

LV1

2023-09-04 20:51:10 - last edited 2023-09-04 22:53:06

Posts: 4

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2023-09-02

Re:AX55 V1 will not go into mesh satellite mode-Solution

2023-09-04 20:51:10 - last edited 2023-09-04 22:53:06

@terziyski

Thanks for that!

So they connect after pushing the WPS wifi button on each unit.

Once they are connected you can no longer log into the AX55 which is what the instructions stated.

We had to leave this morning and these are at a second property where we share a starlink with the neibours, will be interesting to see if they connect back up automatically after the power goes out.

Cheers,

Jon

AX55 V1 will not go into mesh satellite mode

AX55 V1 will not go into mesh satellite mode

Information

Voters 0

Tags