Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

< Deco

I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

COiSman

2023-08-27 11:37:02

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2023-08-27

I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

2023-08-27 11:37:02

Tags:

Model: Deco E4

Hardware Version:

Firmware Version: 1.5.4

I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range, but the Default Gateway is Greyed Out.

3 Reply

David-TP

2023-08-28 02:41:30

Posts: 12324

Helpful: 1704

Solutions: 1084

Stories: 9

Registered: 2020-04-14

Re:I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

2023-08-28 02:41:30

@COiSman

Hi, You might need to change the LAN IP under Deco APP>More>Advanced to 10.0.0.1 first.

Thank you very much and best regards.

Check What's Currently Going on With Deco Deco Early Access Firmware Open for Test! Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.

COiSman

LV1

2023-09-15 17:14:43

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2023-08-27

Re:I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

2023-09-15 17:14:43

@David-TP Thanks for your reply. I tried that but then get the following message: Maybe you can direct me in solving this?

Alexandre.

LV6

2023-09-15 19:13:43 - last edited 2023-09-15 19:14:16

Posts: 3977

Helpful: 2316

Solutions: 505

Stories: 0

Registered: 2020-10-22

Re:I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

2023-09-15 19:13:43 - last edited 2023-09-15 19:14:16

@COiSman

You must have ISP router that you configured with 10.0.0.* IP range. You connected Main Deco to it. You want devices that connect to Deco mesh to be in the same 10.0.0.* IP range.

If this is your current setup, the way to achieve what you want is to configure Deco mesh to run in Access Point mode: Switching a Deco to Access Point (AP) Mode

I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

I want to change the Default Gateway IP address range from 19.168.68.1 to the 10.0.0.1 IP range.

Information

Voters 0

Tags