Home Network Community > Wi-Fi Routers > Archer C64 switching between AP and router mode by itself
< Wi-Fi Routers

Archer C64 switching between AP and router mode by itself

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer C64 switching between AP and router mode by itself

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer C64 switching between AP and router mode by itself
Archer C64 switching between AP and router mode by itself
2023-07-17 14:32:45
Tags: #Access Point Mode #Firmware Update
Model: Archer C64  
Hardware Version: V1
Firmware Version: 1.12.10 Build 230208 Rel.38878n(4555)

Hi, I have Archer C64 1.0

Firmware Version: 1.12.10 Build 230208 Rel.38878n(4555)

I did try in router mode and subsequently in AP mode too, but after a while it randomly switches to the other mode (the one which is currently NOT selected)

This creates a complete hawoc on my network.

What I have noticed is that it shows different version of the firmware when this happens. Is this a feature? or is some sort of setting making it to switch modes arbitrarily? or faulty HW?

Thank you in advance.

  0      
 
  0      
 
#1
Options
3 Reply
Re:Archer C64 switching between AP and router mode by itself
2023-07-17 15:44:01 - last edited 2023-07-17 15:45:35

  @bulva 

 

There's no such setting or feature in C64. The FW version in router mode and AP should be the same.

You can reset C64 to its factory defaults and re-configure from scratch to check if that will resolve the issue.

"Press and hold the WPS/Reset button until all LEDs turn off to reset the router to its factory default settings"

Make sure that the place you've put C64 is well ventilated and the device is not overheating.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:Archer C64 switching between AP and router mode by itself
2023-07-17 16:32:38

  @terziyski 

Thanks for your answer.

Forgot to mention that I indeed did a full reset and also try to reflash the firmware. It didn't help.

Only thing I can try is to downgrade the firmware. It's a mystery. The router is located in the coldest place in the house..garage

  0  
  0  
#3
Options
Re:Archer C64 switching between AP and router mode by itself
2023-07-17 17:19:10 - last edited 2023-07-18 10:02:44

  @bulva 

 

There's no point of downgrading the FW version - 1.12.10 Build 230208 Rel.38878n(4555) is a stable version.

Can you post what are the two different FW versions that are showing in router and AP mode ?

Given this abnormal device behavior, best approach in your case would be to contact your local support and ask for assistance.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 732

Replies: 3

Tags

Access Point Mode Firmware Update
Related Articles
Issue with Archer C64 on access point mode
392 0
 Archer C64 guest network in AP mode has access to LAN
988 0
 Archer C64 cannot access the internet as an AP
897 2
WiFi router not working Archer C64
1504 4
Archer C80. Should I use it in router mode or AP mode?
847 0
archer c64 low speed
268 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.