Official Release Deco Firmware Updates Adding Signal Selection and VPN for Multiple Models
Deco 1.6.0/1.7.0/1.1.0/1.2.0 Firmware Update Added to Select Models!
Over the last few weeks, A New Batch of the Latest Firmware for Deco has been released! This update brings many of the features most requested by the community to reality, including Static Routing, IoT Network, Signal Preference, VPN Server/Client, etc.
Please refer to the Firmware release note for a List of Features Added to Your Model!
| WiFi 5 |
Note: VPN is not supported. |
| Wi-Fi 6 |
|
| Wi-Fi 6E | |
| Wi-Fi 7 |
|
Note:
1. Please make sure your Deco APP is up-to-date.
2. Please be aware that specific features may vary between hardware versions.
3. Some features are not supported under Access Point Mode.
4. If there are other Deco models in the Mesh network, some features would no longer show up, such as Signal Source and Connection Preference; while others only need the support on the main Deco, like VPN, Static Route, MTU, and smart DHCP.
5. As a reminder, the Technical support team does not have any information regarding what models the firmware is being developed for and when we could potentially see a particular release. Please refrain from asking "When Will 'X' Model Receive the Feature?"
Frequently Asked Questions:
1. Why can't I detect the above firmware on the Deco APP?
In the first stage of firmware release, the new firmware would be pushed to a part of users first, then gradually within the next few weeks, if everything goes on well, it will be pushed to all users. During this gap, it is normal if you can not detect the latest firmware. It is suggested to wait for a while or manually update the firmware via web UI per Update the Firmware of Deco.
2. If I have V1.6, which firmware should I use？
Common rules for firmware upgrade: Normally Vx.0=Vx.6/Vx.8 (eg:V1.0=V1.6/V1.8); Vx.x0=Vx.x6/Vx.x8 (eg:V1.20=V1.26/V1.28).
x.6 and x.8 are mainly used to distinguish the place of production.
3. How to downgrade the firmware if I run into any issues?
The newly released firmware feedback is always important and it would be highly appreciated if your could share here what happened to Deco after updating the firmware. We would reply to the post at the earliest time.
In case you have to downgrade the firmware immediately, the cross-platform firmware downgrade, like from 1.2.0 to 1.1.0 needs to be performed via firmware recovery. But if you just want to downgrade from 1.2.6 to 1.2.5 or 1.2.2, it could be done via web UI directly.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@JaapHoutman Doesn't 1.5.8 Build add the source selection option? Did You notice other differences? I don't know it I should try it or wait (thousands of years) for a new firmware for M4 V2...
- Copy Link
- Report Inappropriate Content
Accoring to the documentation the following has been added:
1. Added the support for CWMP;
2. Added the support for Agile Config.
- Copy Link
- Report Inappropriate Content
I'm guessing this is another firmware that the X73-DSL will no receive. I'm still waiting over 18 months to be able to connect Tapo devices to the X73-DSL, whilst the X68s have had 4 firmware releases.
- Copy Link
- Report Inappropriate Content
@Devil1988 TeamViewer
- Copy Link
- Report Inappropriate Content
@Cormacfor2FA Wow, then you will see what they do! That's not nearly requesting remote Access. You should Write correct!
- Copy Link
- Report Inappropriate Content
@JaapHoutman @Fabio25 I can confirm that it doesn't add the option to select signal source on the V2.
- Copy Link
- Report Inappropriate Content
Is this the same functionality as " Support for customizing Satellite Deco signal source" that is currently supported by the M4 V4?
- Copy Link
- Report Inappropriate Content
@JaapHoutman euh, it doesn't add the option.
- Copy Link
- Report Inappropriate Content
@Bever I have updated with the same firmware. I found no difference at all. I don't know of we will ever see a firmware with source selection for Deco M4 V2. I Will soon replace them
- Copy Link
- Report Inappropriate Content
@David-TP This is what's happening daily after updating the X50 to the latest 1.2.7 Build 20230620 Rel. 31797 firmware. The X50 is my sub-mesh that is connected to the G2H camera. My camera keeps goin on and off all day long.
Tried all the basic troubleshooting, not working.
The main X50-4G is still running on the awfully old fimware version 1.10 Build 20221201Rel. 70625 from last year.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 31680
Replies: 123
Voters 0
No one has voted for it yet.