Home Network Community > Feature Request (Deco) > IPv6 for LAN: request SLAAC for Android clients
< Feature Request (Deco)
 
4
Votes

IPv6 for LAN: request SLAAC for Android clients

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
 
4
Votes

IPv6 for LAN: request SLAAC for Android clients

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
IPv6 for LAN: request SLAAC for Android clients
IPv6 for LAN: request SLAAC for Android clients
2022-11-19 15:01:11
Tags: #IPv6
Model: Deco X50  
Hardware Version: V1
Firmware Version: 1.0.9

Hello TP-Link

 

When Deco X50 assigns IPv6 address to LAN clients it uses DHCPv6.

Background: my ISP provides IPv6 to Deco via DHCPv6-PD, so Deco can

assign addresses to the LAN clients.

 

However Android clients cannot do DHCPv6 and do not get IPv6 addresses.

 

I believe Android clients are forced to depend on SLAAC.

#1
Options
4 Reply
Re:IPv6 for LAN: request SLAAC for Android clients
2022-11-21 09:35:08 - last edited 2022-11-21 09:35:32

  @marichyasana167 

Hi, have you checked on the Deco APP whether Deco X50 has got an IPV6 address first?

And Have you tried to change the Assigned type here:

Internet connection type---Dynamic IP.

Assign type---SLAAC

Wait for your reply.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
#2
Options
RE:IPv6 for LAN: request SLAAC for Android clients
2023-04-10 17:16:08
Not just for android but for any IPv6 client including iOS, Windows, Linux and Android. This should inlcude options for IPv6 pasthrough and IPv6 p[refix management
#3
Options
RE:IPv6 for LAN: request SLAAC for Android clients
2023-04-14 12:11:01

  @tga516 

Hi, Thanks for your message.

I have to admit that I am always a little confused about IPV6.

For the IPV6 passthrough, I believe you want to make the IPV6 firewall on Deco turned off by default since now it is set to block all outside access.

As for the IPV6 prefix management, do you mean the LAN Address prefix?

Would there be any specific reason that you want IPV6 prefix management?

Thank you very much.

best regards.

 

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
#4
Options
RE:IPv6 for LAN: request SLAAC for Android clients
2023-07-23 10:33:54

  @David-TP 

 

I am following up as I'm having the same issue.

 

Your response David is that he should change his WAN setting to SLAAC.  That is not the issue.  The issue is the router delivering IPV6 addresses on the LAN side via SLAAC.

 

Android devices only received ipv6 via SLAAC, so using SLAAC on the LAN side is critical to a fully functioning router.  The WAN side settings work fine on the TP-Link, but the LAN side needs to support SLAAC.

#5
Options

Information

Helpful: 4

Views: 1077

Replies: 4

Voters 4

voter's avatar
voter's avatar
voter's avatar
voter's avatar

Tags

IPv6
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.