Attaching a backup internet, Will it Combine the Speed?
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
What if i connected a backup internet connection to the WAN port so that i have a one connection through the vdsl (landline) [30 Mbps] port and another connection through the WAN [30 Mbps] port.
Will the VR600 act as a load balancer and combine the speeds of both connections? So that if i made a speed test on like fast.com or speedtest.net I will get a speed of 60 Mbps?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
No, with VR600 you can't do load balancing. It's either DSL port (DSL modem router mode) or WAN/LAN4 port (wireless router mode) you can use at a time.
There's a special devices - load balancers or VPN routers, which will allow you to do that in addition to your existing VR600.
- Copy Link
- Report Inappropriate Content
I believe that in your case, either would do the job.
Check this comparison.
R480 is rack mountable (bigger) and has an internal power supply. It also supports up to 30000 concurent sessions.
pfSense firewall/router software can be installed on any small computer with three or more network cards and serve as a load balancer and redundancy when using two ISPs.
In your case it replaces the load balancer device - topology stays the same. The hardware you could use for installing pfSense, can be seen in this video. pfSense can't be installed on a TP-Link device.
TD-W9960 supports Bridge mode. Here's an exmaple how to configure in bridge mode.
Except the redundancy you'll have the load balancing as well.
- Copy Link
- Report Inappropriate Content
No, with VR600 you can't do load balancing. It's either DSL port (DSL modem router mode) or WAN/LAN4 port (wireless router mode) you can use at a time.
There's a special devices - load balancers or VPN routers, which will allow you to do that in addition to your existing VR600.
- Copy Link
- Report Inappropriate Content
And What is the difference between a load balancer and a VPN router?
Also, what is the right and optimal setup using a load balancer if i have two landlines with vdsl2 subscription?
Maybe also you can consider that i have 2 VR600 modem routers, and that i still need to have wifi coverage out after the load balancer.
Many thanks
- Copy Link
- Report Inappropriate Content
@Errefae .
VPN routers are part of the Omada SDN. Most of them offer a gigabit WAN/LAN ports and support load-balancing features as well.
Load balancers are targetted specifically for load balancing work - they are usually with 100mbit/s WAN/LAN ports.
The best topology in such case is:
DSL modem (bridge mode) DSL modem (bridge mode)
| |
|------------------------ Load-balancer ---------------|
|
|
Wireless Access Points
Thus, you'll avoid the double NAT in your network and the load-balancer would be the main router/firewall and management point for your network.
But you won't be able to use your two VR600 DSL modem routers wireless radio - that's why you'll need an additional wireless APs.
You can find more information regarding business routers and Omada SDN in the community business section.
- Copy Link
- Report Inappropriate Content
I prefer to use the VR600s wireless features, can i use them as Wireless APs? The load balancer connects to both of them or the load balancer connects to one of them and the second VR600 connects to the First VR600 on LAN. What do you think?
In this case does tp-link has Vdsl2 modems?
- Copy Link
- Report Inappropriate Content
If you want to use VR600 as APs use this guide. You can daisy-chain them or connect each one directly to the load-balancer.
Here's the list of VDSL2 modem routers.
- Copy Link
- Report Inappropriate Content
1- Does the load balancer has dhcp server?
If this is the topology, will it work?
M: Modem
Load: Load Balancer
S: Switch
PC: computer
A: Access points (VR 600 v3)
Many thanks
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I believe that in your case, either would do the job.
Check this comparison.
R480 is rack mountable (bigger) and has an internal power supply. It also supports up to 30000 concurent sessions.
pfSense firewall/router software can be installed on any small computer with three or more network cards and serve as a load balancer and redundancy when using two ISPs.
In your case it replaces the load balancer device - topology stays the same. The hardware you could use for installing pfSense, can be seen in this video. pfSense can't be installed on a TP-Link device.
TD-W9960 supports Bridge mode. Here's an exmaple how to configure in bridge mode.
Except the redundancy you'll have the load balancing as well.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2142
Replies: 21
Voters 0
No one has voted for it yet.