Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
yes. It's insanely hot. The tech that came to install my internet said he's never seen a router that hot before and said he was concerned.
- Copy Link
- Report Inappropriate Content
@David-TP Just checked my primary M9 with an IR thermometer "gun" - it's 34.5C. (Room temp is 20C).
(ps still on 1.5.6 firmware)
- Copy Link
- Report Inappropriate Content
@rekeen01 @iresLeandro @LaurieR
Thanks for the feedback.
Due to the flat design of the Deco M9 plus, its outer cover is closer to the cooling module and you may feel warmer than the models having a cylinder design, like Deco M4. However, it's confirmed strictly that Deco could work continuously without any problems/safety hazards at a room temperature of 40 °C/104°F due to the test results in TP-Link's lab.
So A cool and well-ventilated environment is ideal for Deco products, it is suggested to:
1. Put your Deco in the open, do not cover your Deco with any objects, avoid placing your Deco in a closed space, and don’t let it suffocate.
2. Avoid placing your Deco on top of any running electronic devices. Putting two electronic devices together would greatly increase the surrounding temperature, which is bad for the Deco and the device beneath it.
3. Keep your Deco away from direct heat (like fireplaces and space heaters) or excessive sunlight.
4. Use the original power adapter that came with the Deco.
5. If possible, You may find a mounting bracket for Deco products. In this case, the heat dissipation will be better than before.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi, the official firmware has improved the network performance issue that was reported on the beta firmware.
I think the disconnection might be related to the Ethernet Backhaul on Deco.
Do you have a network switch between the main Deco M9 plus and 4 other satellite Deco M9 plus units?
It is also suggested to have a look at this link:
General questions about Ethernet Backhaul feature on your Deco Q5+Q6
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP where can i find the official release for the 1.6.x update for my deco m9 plus?
- Copy Link
- Report Inappropriate Content
hey, I think they said a few days ago that it will be available in a few weeks. My guess is it should be available through the app, you shouldn't have to download it from the website.
- Copy Link
- Report Inappropriate Content
M9 Plus will never be on same version as M5. I was manager to another household with M5. I always envy the update they got while the more premium M9 was left out. The developer and the publisher button to release the M9 to public was maybe wrongly configured to always release M5.
- Copy Link
- Report Inappropriate Content
That's exactly what people won't understand. TP Link 'punishes' the customers buying the premium product by offering them less support and updates. They offer even more premium mesh products now but I'm afraid to upgrade my system.... I think my next upgrade will be to a different brand.
- Copy Link
- Report Inappropriate Content
Indeed, TP-Link is just a commercial junk producer.
They want to sell but don't care about users.
Check the Google Pro routers.
Or please share your advise 🙂
- Copy Link
- Report Inappropriate Content
They are releasing WiFi 6 and 7 products without being able to support WiFi 5.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 111781
Replies: 440
Voters 2
