Official Release Deco M9 Plus 1.6.4
Current Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.4_Build_20240718
Release Note:
1. Improve the device stability;
2. Enhance the system security
---------------------------------------------------------------------------------------------------
History Release
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.3_Build_20231225
Release Note:
1. Fix the potential security vulnerability and its related problem.
2. Improve system stability and security.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.2_Build_20230906
Release Note:
1.Fixed the bug that parental control doesn't take effect.
For Deco M9 Plus(V1/V2/2.2)
Deco M9 Plus_1.6.1_Build 20230403
Release Note:
1. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
2. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
3. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
4. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
5. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
6. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
7. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
8. Fixed the bug that the built-in speedtest has low speed test results.
Notes:
1. This firmware downgrade could be done via firmware recovery-How to use firmware recovery.
2. Please update your Deco APP to the latest version for the new features.
3. If there are non-1.6.0 models in the Mesh network, you may miss some new features but this feature will be supported via firmware update in the future.
4. You may miss some new features when Deco is set to Access Point mode.
Related Articles:
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I've also been experiencing some strange disconnects on my devices. After upgrading everything was fine for a few days but then noticed some devices flapping. I've turned off fast roaming a d it seems to have helped as mentioned. It's not all devices that have issues. So far I've noticed my Samsung s22u and my Logitech harmony hubs and one Samsung tv.
- Copy Link
- Report Inappropriate Content
Hi @David-TP , any feedback please?
--
After a week of experimenting with global "Fast roaming" and individual tweaking, it's a no go for me.
The benefits of selecting preferred connection sources are way less than the stability of the connection when walking through my property.
I've been using the same router setup (6 x Deco M9 Plus) without big issues while using 1.5.6, but this version 1.6.0 destroys the benefits of Fast roaming.
Can you please instruct me how to go back to 1.5.6_211018?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Will my whole setup be destroyed?
- Copy Link
- Report Inappropriate Content
Thanks for the feedback.
I used to see there are several different versions of parental control on our products and one of the old version is just like what you want " release only some access at certain times", such as https://www.tp-link.com/en/support/faq/1531/ and gradually more newer models apply to the latest version of parental which is what you have seen on Deco M9 plus. It is not likely the engineers will bring it back but it would be highly appreciated if you could start a new thread here to let me know how many other users would have the same request, So that the engineers would have the chance to know what is best for users.
Best regards.
- Copy Link
- Report Inappropriate Content
Hi, Sorry for the delay.
From firmware 1.6.0 to 1.5.x, takitkat is right and it needs to done via firmware recovery first.
There would be a better way to do it to save the current configuration:
1. Pick one of the satellite unit and do the firmware recovery first and restore it back to 1.5.7.
2. Then add it back to the previous mesh network and change it to be the main Deco.
3. After that, you could perform the firmware recovery on two other Deco M9 plus.
- Copy Link
- Report Inappropriate Content
Hi @David-TP ,
Thanks for the clarification.
I tried the downgrade of 1 Deco (as suggested) to version 1.5.6 but after the downgrade, it was unable to connect to the network again. The LED stayed red-blinking.
Did it twice, without any luck.
I finally upgraded again to 1.6.0 and went back online.
But, still, I have an unstable set of 6 x Deco M9 Plus.
So, conclusion, downgrade is unreliable, as the Deco's are now.
So, please remind the development team to quickly fix the unstable (fast) roaming behaviour. And, as you can see in other posts on this thread, I'm not the only one.
- Copy Link
- Report Inappropriate Content
Thanks a lot for the update.
Now, there is a new version that has optimized this feature and if you are interested, please refer to the private message to install the new firmware.
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP is the new update available for everyone? Or is 20220810 still the latest beta version?
- Copy Link
- Report Inappropriate Content
@David-TP same here. id like to test it out as well pls
- Copy Link
- Report Inappropriate Content
Information
Helpful: 10
Views: 112517
Replies: 440
Voters 2
