Home Network Community > DSL Modem Routers > Archer VR400 v3 - Modem Only Mode
< DSL Modem Routers

Archer VR400 v3 - Modem Only Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer VR400 v3 - Modem Only Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer VR400 v3 - Modem Only Mode
Archer VR400 v3 - Modem Only Mode
2022-05-25 16:36:56 - last edited 2022-05-26 00:48:18

Hello,

I am looking to buy an Archer VR400 v3 for a specific use case.

 

I have a pfSense device acting as a router handling internal firewall/dns/dhcp etc.

 

My ISP provided device does not offer a modem only mode which causes some instability and I would like to replace with a device that can work in a modem only mode, on paper he Archer Vr400 v3 fits the bill.

 

Can I check that I can:
 

  1. Set up the device with he generic user name and password provided to my by my IPS (BT here in the UK)
  2. Set the Archer VR400 v3 to be modem only wih the instructions detailed here: https://www.tp-link.com/uk/support/faq/2728/
  3. Plug my WAN port of my pfSense device into the VR400 v3 and thats it?!

 

In my current setup I need to configure the pfSense device's WAN port to have an IP address in the same range as my ISP device (192.168.xxx.xxx) and my LAN port to use the internal address (172.16.xxx.xxx), in the new setup what IP address will the WAN port need, will it still use the 192.168.xxx.xxx range that is default on the Archer VR400 v3?

I can't quite get my head around how the IP address a device in modem only mode works, I assume it will have a public facing IP address from the ISP, but what would need to be configured between the modem and the pfSense router

Thanks in advance

  0      
 
  0      
 
#1
Options
3 Reply
Re:Archer VR400 v3 - Modem Only Mode
2022-05-25 18:37:12 - last edited 2022-05-26 00:48:18

  @Camnomis 

 

I don't know about the pfSense in particular, but if the device in place of the pfSense was, for example, a generic Wi-Fi router or a Windows PC with Ethernet port, then you would setup the Internet connection on that Wi-Fi router or Windows PC by selecting "PPPoE" as connection type and enter the username and password from the ISP into the provided entry fields. Then save the connection and click "connect". That's normally all that is necessary to get online via a DSL modem.

 

There will usually be some advanced settings available in the configuration dialog, like adjustment of the "MTU Size", setting custom DNS' IP addresses, etc., but you can play with those later if you think you need to.

 

  0  
  0  
#2
Options
Re:Archer VR400 v3 - Modem Only Mode
2022-05-25 18:49:30 - last edited 2022-05-26 00:48:18

  @woozle 

 

thanks, would the PPPoE user name and password not be set in the VR400 rather than anything connected to it?

  0  
  0  
#3
Options
Re:Archer VR400 v3 - Modem Only Mode
2022-05-25 19:21:37 - last edited 2022-05-26 00:48:18

  @Camnomis 

 

If you switch the VR400 into Modem-Only mode by selecting Connection Type "Bridge", then the device that you connect to the LAN port of the VR400 needs to establish the Internet connection.

 

If you want the VR400 to establish the Internet connection, then you need to select Connection Type "PPPoE" on the VR400, but this means the VR400 will remain to be a Modem Router.

 

If you don't care about the Double-NAT issue, then either way should work for you.

  2  
  2  
#4
Options

Information

Helpful: 0

Views: 1774

Replies: 3

Related Articles
Archer VR400 Modem Mode/Transparent Bridging Mode
5348 0
Archer VR400 / AC1200 Bridge Mode / modem only for use with Deco
20848 0
 Archer VR400 v3
664 1
How to disable Onemesh Hidden network on modem vr400 v3
10569 6
 Archer VR400 v3 - Bridge Mode Question
799 0
Archer vr400 AC1200 v.3 wireless problem
701 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.