Home Network Community > Deco > HELP! How to setup deco mesh to accept 2 ISP?
< Deco

HELP! How to setup deco mesh to accept 2 ISP?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

HELP! How to setup deco mesh to accept 2 ISP?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
HELP! How to setup deco mesh to accept 2 ISP?
HELP! How to setup deco mesh to accept 2 ISP?
2022-04-07 08:25:53
Model: Deco M9 Plus  
Hardware Version:
Firmware Version:

Hi, I have 2 ISP providers going into 2 separate m9 deco.

 

What do I need to configure/buy so that I can place both ISP to a single m9 deco (so i can use the 2nd one as an extender)

 

Thanks in Adavnce!

  0      
 
  0      
 
#1
Options
6 Reply
Re:HELP! How to setup deco mesh to accept 2 ISP?
2022-04-07 15:16:42 - last edited 2022-04-07 15:17:01

  @2ku2cool 


 

You will need to get dual-WAN router which can handle two ISPs. Then, connect Main Deco to that router.

 

Google  this: Best Dual Wan Routers (Best Business Firewall Routers in 2021)

 

For some reason, I can't put link in my reply, but this is article from site MBReviews, posted on MAY 17, 2021 by Mark B

  1  
  1  
#2
Options
Re:HELP! How to setup deco mesh to accept 2 ISP?
2022-04-07 15:25:55
i've tried a few and it's a problem for anything involving transactions (buying anything online). i was hoping tplink has an answer, since they do sell a dual wan router
  0  
  0  
#3
Options
Re:HELP! How to setup deco mesh to accept 2 ISP?
2022-04-08 02:18:21

  @2ku2cool 

Hi, we do have some models that support Dual -WAN connection, such as ER605:

https://www.tp-link.com/business-networking/vpn-router/er605/

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
  0  
  0  
#4
Options
Re:HELP! How to setup deco mesh to accept 2 ISP?
2022-04-08 09:12:43
does it have exact instructions on using it on a deco mesh?
  0  
  0  
#5
Options
Re:HELP! How to setup deco mesh to accept 2 ISP?
2022-04-08 11:33:06 - last edited 2022-04-08 11:40:27

  @2ku2cool 

Hi, I didn't see any instructions yet.

For the multi-wan configuration on ER605, you might need to enable an additional WAN port on the web UI.

When it comes to Deco, the following layout is much more recommended:

the Deco is in access point mode: How to set up Deco to work in Access Point mode?

or if you refer to Ethernet backhaul, the connection methods on this link work too: 

General questions about Ethernet Backhaul feature on your Deco

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶KidShield Now Open for Trial! Try to leave a Message if urgent help is required.
  0  
  0  
#6
Options
Re:HELP! How to setup deco mesh to accept 2 ISP?
2022-04-08 12:19:38
the last time I did this with a Cisco/Linksys RV042G, I ran into problems when the site I connect to authenticates the link. Ex. 1) I connect to bank with ISP1 2) mid transaction, load balancing router switches me to ISP2 3) bank site does not accept transaction Will I still be plagued with this problem?
  0  
  0  
#7
Options

Information

Helpful: 0

Views: 835

Replies: 6

Related Articles
Deco M9+ setup
1050 0
Cant setup Deco M9 plus as main deco in the mix Mesh network of M5 and M9 plus
1211 0
DECO M9 setup with Etisalat
845 0
 validate mesh setup
1787 0
 Mesh wifi setup
2484 0
Need to setup a SECOND mesh system with second ISP.
117 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.