Home Network Community > Deco > My x20 wont daisychain
< Deco

My x20 wont daisychain

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

My x20 wont daisychain

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
My x20 wont daisychain
My x20 wont daisychain
2022-03-11 07:28:24
Model: Deco X20  
Hardware Version: V1
Firmware Version: 2.0.3 Build 20201120 rel 58079

Its actually a version 1.2 NZ

Have 3 nodes.  Main is upstairs etherneted to router, node 2 is downstairs and node 3 is in the garage/office about 10 paces from node 2. Node 3 and node 2 are roughly in line of sight of each other. I cant get node 3 to connect to node 2 even though node 2 is way closer than the main node.  How do I get node 3 to daisychain off node 2. Am presently using the wireless router (recommended) operation mode, should I use the access point mode instead? Or any other ideas.

  0      
 
  0      
 
#1
Options
4 Reply
Re:My x20 wont daisychain
2022-03-11 07:49:28

  @Allan_Nicol67 

Hi, the operation mode might not be related and it is suggested to have a look at this link:

Manual Signal Source Selection on Deco

since the distance is not the only factor that decided the signal source, the position of the satellite units and the barriers around all needs to be concerned.

Have you noticed an issue when RE node 3 did not link to RE node 2?

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:My x20 wont daisychain
2022-03-11 08:35:00

  @David-TP thanks Dave, where do I find that in the settings that you are refering to ? 

  0  
  0  
#3
Options
Re:My x20 wont daisychain
2022-03-11 08:41:43

  @David-TP thanks Dave, so Deco is deciding that if the 3rd node is connecting to the main then thats the best fit?  Is just that the wifi signal is down to 2bars in the office but node 2 still has 3 bars, is there a fix for x20's as I didnt see that in your link ? Thanks in advance for your help :)

  0  
  0  
#4
Options
Re:My x20 wont daisychain
2022-03-14 08:05:05

  @Allan_Nicol67 

Hi, you could send an email to support.forum@tp-link.com with the information mentioned here in the recommended solution so that the engineers could help us run a further check whether Deco made the right choice for signal source.

 

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 685

Replies: 4

Related Articles
Daisy Chain Deco X20
767 0
 X20 will not daisy chain
2565 0
 X20 will not daisy chain
687 0
Dell PC wont connect to Deco X20. message Unable to connect to this network.
653 0
 RE300 - Daisychain
971 0
X20 with AC2800
668 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.