Access point

2021-09-09 21:30:12 - last edited 2021-09-10 22:43:25

Posts: 26

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-07-07

Access point

2021-09-09 21:30:12 - last edited 2021-09-10 22:43:25

Model: Archer C50

Hardware Version:

Firmware Version:

I have a Archer C50 which I installed to try and rectify a case of overloading my 2.4 band ..unfortunately it has not used the problem ..I have now bought a cheap mesh system Mercury ac1200 which I have been told is by Tp link , what I want to know is can I use it as a acces point and add it to my mesh system to boost my WiFi system to my mancave thanks

1 Accepted Solution

LV2

2021-09-09 22:51:28 - last edited 2021-09-10 22:43:25

Posts: 26

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-07-07

Re:Access point -Solution

2021-09-09 22:51:28 - last edited 2021-09-10 22:43:25

@terziyski many thanks a lot to learn ..lol

Recommended Solution

11 Reply

LV7

2021-09-09 22:02:54 - last edited 2021-09-09 22:12:06

Posts: 6924

Helpful: 5161

Solutions: 1111

Stories: 7

Registered: 2013-10-12

Re:Access point

2021-09-09 22:02:54 - last edited 2021-09-09 22:12:06

Archer C50 supports AP mode natively since HW v4 - AP mode (case 1)

If yours is below HW v4 you can use AP mode (case 2).

Here's how to determine the HW version of your device.

In either case C50 can work as a standalone AP, connected by ethernet cable to your mesh system.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

LV2

2021-09-09 22:11:23

Posts: 26

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-07-07

Re:Access point

2021-09-09 22:11:23

@ukmartian HWV4 do not understand that ...sorry so I will have to connect it via a Etherley cable it can't be done via wireless any way sorry for the ignorance

LV7

2021-09-09 22:22:06 - last edited 2021-09-09 22:48:58

Posts: 6924

Helpful: 5161

Solutions: 1111

Stories: 7

Registered: 2013-10-12

Re:Access point

2021-09-09 22:22:06 - last edited 2021-09-09 22:48:58

HW is the hardware version of your device. See my first post for details how to determine which one is it.

If you can't run a cable to the C50, then you can try the following:

If you have an operation mode Range Extender (HW v6), you could try to extend your mesh wireless coverage - Chapter 6 in C50 user guide:

If you have a HW v4 or below you could try using the WDS Bridging to extend your mesh wireless coverage - FAQ/Q4 in C50 user guide:

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

LV2

2021-09-09 22:51:28 - last edited 2021-09-10 22:43:25

Posts: 26

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-07-07

Re:Access point -Solution

2021-09-09 22:51:28 - last edited 2021-09-10 22:43:25

@terziyski many thanks a lot to learn ..lol

Recommended Solution

LV2

2021-09-10 22:52:26

Posts: 26

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-07-07

Re:Access point

2021-09-10 22:52:26

@ukmartian hi again , I have got my mesh system it is a mercusys Halo S12 which I believe is by TP Link ..if not ignore this , my question is can I assign a seperate ssid for the 2.4 and 5ghz bands, I have done this on my modem , it makes it easier to log smart devices onto the network as they only work on 2.4 mhz this avoids logging in a turning off the 5ghtz band everytime if I want to reinnitialise or install a new plug thanks ..

LV7

2021-09-11 08:14:33

Posts: 6924

Helpful: 5161

Solutions: 1111

Stories: 7

Registered: 2013-10-12

Re:Access point

2021-09-11 08:14:33

Judging by its web interface you can't use a separate SSIDs for the 2.4 and 5 GHz bands:

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

LV2

2021-09-11 13:48:48

Posts: 26

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-07-07

Re:Access point

2021-09-11 13:48:48

@terziyski many thanks that is the same as the router, It means I also can use the same ssids and passwords meaning I won't have to re install or relogin my plugs etc....will I only have to do this to the master or all off them

Many thanks..brilliant and helpful forum

Steve

LV7

2021-09-11 14:29:36

Posts: 6924

Helpful: 5161

Solutions: 1111

Stories: 7

Registered: 2013-10-12

Re:Access point

2021-09-11 14:29:36

You'll know that when you set the same SSID and password and observe if the plugs are re-connecting successfully.

If they don't, then you have to re-add them, because depending on the smart device type, it could be bound to the wireless router MAC address as well.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

#10

LV2

2021-09-11 19:28:11

Posts: 26

Helpful: 3

Solutions: 1

Stories: 0

Registered: 2021-07-07

Re:Access point

2021-09-11 19:28:11

@terziyski hopefully they will...the did when I changed from the VM hub 3 router to the TP LINK but that is another reason why I am separating the bands if a combined you have to go into setting and turn off the 5 when separate it seem ok...so far thanks for the feedback..i will install everything when I get a quiet few minutes...

#11