New Release Onemesh Firmware for Archer AX10
Hello everyone,
The Onemesh firmware for Archer AX10 is now available, customers who own the router can update the firmware to enjoy the mesh network with the range extender/powerline extender.
Customers can check for the new firmware on the router web GUI or via the Tether app, they can also download the firmware from the TP-Link official website to upgrade the router manually.
Note: Please check the device label to verify the country code and hardware version of your device first, and choose the correct file to download and install.
If you have already connected a range extender to the AX10 network, check this guide to re-build them into Onemesh network:
https://www.tp-link.com/support/faq/2509/
Release note for the firmware:
New Features/Enhancement:
1. Added OneMesh feature;
2. Updated IPTV Profile;
3. Added System Time feature on Tether App;
4. Added QoS Schedule feature;
5. Added a prompt when the negotiation rate of the WAN port is 100Mbps;
6. Optimized the Parental Control feature;
7. Added dual NAT detection and Internet Online time feature on Tether App;
8. Maximum number of clients on the single-band network increased to 128;
9. Added IPTV feature on Tether App;
10. Optimized the Client List;
11. The wireless default encryption method is modified to WPA2+AES.
Bug Fixed:
1. Fixed the FragAttacks vulnerabilities;
2. Fixed the bug that the router incorrectly blocked Internet requests;
3. Fixed the potential shell illegal injection risk of the read and write instructions of the tddp module;
4. Fixed the display error on Network Map page in some cases;
5. Fixed the bug that TKIP encryption was not supported under 11ax only mode;
6. Fixed the bug that Web UI cannot synchronize the operation of deleting UPNP entries;
7. Fixed the bug that the PPTP VPN server feature can't be enabled and the account can't be deleted in some cases;
8. Fixed the bug that the router failed to save system log in AP mode;
9. Fixed the bug that AX10-TDDP causes RCE vulnerabilities;
10. Fixed uhttpd Directory Traversal vulnerabilities;
11. Fixed the bug that Tether app failed to show the IP address in some cases;
12. Fixed the bug that the client type cannot be changed on the Tether App;
13. Fixed the bug that client icon can't be set to other on Tether App.
Do let the community know if there is an issue.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Tried a hard reset on the router, disabled onemesh.
The 5Ghz signal and speed are horrible. Tried multiple channels. Router is in the exact same position as before.
2.4Ghz and LAN are working fine.
It is definitely the new firmware.
- Copy Link
- Report Inappropriate Content
We have reported the issue to the support engineers, they will likely reach out to you via email to continue to troubleshoot your issue.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I have issues since i upgraded firmware on EU V1, WDS connection with a C6 EU V2 router doesn't work anymore.
- Copy Link
- Report Inappropriate Content
Just to confirm, is the AX10 the main router, and the C6 is the extender? Were they connecting fine via WDS before the AX10 firmware update?
After the firmware updated on the AX10, and you configured the WDS settings on the C6, what is the WDS status on its web interface, is it RUN? Please show us the screenshot.
Please also refer to this guide to double check the basic settings on the C6, try to reset both AX10 and C6 to confirm if they can connect again:
https://www.tp-link.com/support/faq/1555/
- Copy Link
- Report Inappropriate Content
Kevin_Z wrote
Just to confirm, is the AX10 the main router, and the C6 is the extender? Were they connecting fine via WDS before the AX10 firmware update?
After the firmware updated on the AX10, and you configured the WDS settings on the C6, what is the WDS status on its web interface, is it RUN? Please show us the screenshot.
Please also refer to this guide to double check the basic settings on the C6, try to reset both AX10 and C6 to confirm if they can connect again:
https://www.tp-link.com/support/faq/1555/
Yes, it is the actual configuration, they were connecting fine before the AX10 firmware upgrade, and after performing the update, the WDS status was still RUN, but the connection issue started here.
I tried rebooting both devices but it didn't solve the problem. Every step in the tutorial have been respected.
- Copy Link
- Report Inappropriate Content
Does this mean the WDS status on the C6 is RUN, but you cannot get internet access when connecting to the C6 wireless network? Are you able to get a valid IP address from the network? Is it assigned by the AX10 correctly?
If the devices can get a correct IP address from AX10, please try to do a simple ping test, ping the IP address of the AX10, then show us the result.
BTW, we will follow this up via email later.
- Copy Link
- Report Inappropriate Content
Kevin_Z wrote
Does this mean the WDS status on the C6 is RUN, but you cannot get internet access when connecting to the C6 wireless network? Are you able to get a valid IP address from the network? Is it assigned by the AX10 correctly?
If the devices can get a correct IP address from AX10, please try to do a simple ping test, ping the IP address of the AX10, then show us the result.
BTW, we will follow this up via email later.
The WDS status is Run, but connecting computers via Ethernet ports on the C6 doesn't work anymore.
Fore some reasons, i chose to keep C6 DHCP server activated and managing his own part of the subnet, but this subnet is the same as the AX10 (C6 DHCP owns range from 192.168.1.151->254 and AX10 DHCP owns range from 192.168.1.30->150). C6 DHCP sets AX10 address (192.168.1.1) as gateway on devices. C6 address is set at 192.168.1.20.
Then on devices, pinging the AX10 address fails.
I will try to set AX10 as only DHCP server on the subnet and tell you the result.
Edit: finally, i was able to make it works, but this is a weird thing. I wanted to revert back to official firmware on the C6 because i used an OpenWrt one since the issue appeared, just to test what you wrote, but i was stuck to push the last firmware via TFTP method, and i had to use the first released one instead (1.0.1 Build 20180627)
Starting to configure the C6 with the original firmware, i noticed a 'WDS Mode' option in the advanced parameters section, where to configure the WDS connections.
I was only able to make WDS works using the 'WDS 1' option, the two others 'Auto' and 'WDS 2' didn't work, and i tried with 2.4GHz and 5Ghz.
Upgrading the C6 firmware to the latest, 'WDS Mode' option disappeared, and if i didn't set 'WDS 1' running the old firmware, WDS can't work running the new one, and i'm sure of that.
So it can be a nice thing to bring back the 'WDS Mode' option in future firmware release
- Copy Link
- Report Inappropriate Content
That's great to know the WDS is running again on the C6 now. Your suggestion about the WDS mode will be recorded on the system, and the engineers will evaluate how to achieve that in the future firmware updates.
- Copy Link
- Report Inappropriate Content
Archer AX10 updated Firmware can’t use China web
Model: Archer AX10
Hardware Version: V1.2
Firmware Version: Archer AX10(US)_V1.2_210421
I am in South Korea
PING ys.mihoyo.com (117.25.153.244): 64 data bytes
Request timed out!
Request timed out!
Request timed out!
Request timed out!
Request timed out!
Request timed out!
Request timed out!
Request timed out!
--- Ping Statistic "ys.mihoyo.com" ---
Packets: Sent=8, Received=0, Lost=8 (100.00% loss)
ping is stopped.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 23667
Replies: 113
Voters 0
No one has voted for it yet.