Home Network Community > Wi-Fi Routers > TPLink Archer C4000 resets to factory default during my internet provider maintenance work
< Wi-Fi Routers

TPLink Archer C4000 resets to factory default during my internet provider maintenance work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TPLink Archer C4000 resets to factory default during my internet provider maintenance work

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TPLink Archer C4000 resets to factory default during my internet provider maintenance work
TPLink Archer C4000 resets to factory default during my internet provider maintenance work
2021-04-28 13:37:06
Model: Archer A20  
Hardware Version: V3
Firmware Version: 1.0.3 Build 20191026 rel.13901

My router reset to factory default by itself during my internet provider 6 hours long maintenance. 

 

That is a very weird situation that I run into. How could a router reset to the factory default by itself? Wonder if anyone runs into this?

 

My bad also, I didn't have a backup or don't remember where I put the backup config file, I had to reconfigure the router and all the devices in the house. Will have to keep a good back. 

 

However, I am very disappointed at this router now.

 

 

William

 

 

 

 

  0      
 
  0      
 
#1
Options
2 Reply
Re:TPLink Archer C4000 resets to factory default during my internet provider maintenance work
2021-04-28 17:19:14

@WilliamTS Reading more, I think I had a similar situation as in this thread https://community.tp-link.com/en/home/forum/topic/99402

 

While I was troubleshooting the network issue caused by the internet provider outside of their planned maintenance window, I did press the power buttons a couple of times and also unplug the power once or twice for a brief time to reset the router.  But the router should never reset to factory defaults! I do worry about this router now.

 

 

  0  
  0  
#2
Options
Re:TPLink Archer C4000 resets to factory default during my internet provider maintenance work
2021-04-29 03:35:48

@WilliamTS 

 

You may reset the router to factory defaults manually again, reconfigure it from scratch to connect to the internet again, then monitor if the issue will happen again. Do pay attention to if this issue will happen with some specific operation like power off then on frequently, or anything special that you can observe.

 

If the router restore to defaults again automatically without any clear clue, then contact the reseller or the local tech support to request a replacement if it is still under warranty:

https://www.tp-link.com/support/contact-technical-support/#Hotline-Support

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#3
Options

Information

Helpful: 0

Views: 494

Replies: 2

Related Articles
TPLink Archer C4000 resets to factory setting after power outage
2492 0
Traffic monitoring on the TPLINK C4000 Archer A20 WiFi router
1783 0
Archer C4000 loses setup to factory default and password gets changed.
456 0
Router Tp-link archer c4000
506 0
TPLink Router resets to default for a "front end conflict"
519 0
Router Failure Archer C4000
602 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.