Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

< Deco

Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

NativeCanadian

2021-02-02 03:52:47

Posts: 6

Helpful: 3

Solutions: 0

Stories: 0

Registered: 2021-02-02

Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

2021-02-02 03:52:47

Model: Deco X60

Hardware Version: V2

Firmware Version: 1.2.6

Hello,

I am having an issue with my TP-Link switch enabling loop protection when I use wired backhaul on the Deco X60.

My setup is modem with main Deco X60 connected

Then the switch is connected to the other port on the X60

Then three more Deco X60 are connected to the switch

The problem is that the switch disables the main deco from connecting as it goes into loop protection mode. In this scenario the closest deco wirelessy connects to the main deco and since all are on the switch

As soon as I disable loop protection on the switch they all work normally and report they are all connected by enternet.

So far it seems to work, BUT I should be able to use loop protections AND why is this happening

So again, I am using the STAR pattern to connect and the switch is a tp-link.

Modem

Main DECO

TP-Link Switch (TL-SG1016PE)

| | |

DECO DECO DECO

I get loop detection at main DECO and port is shut down

4 Reply

NativeCanadian

LV1

2021-02-02 23:28:12

Posts: 6

Helpful: 3

Solutions: 0

Stories: 0

Registered: 2021-02-02

Re:Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

2021-02-02 23:28:12

Are there any Admins or TP-Link Gurus that can explain to me what is happening and how to make it stop happening?

I feel that the Decos still ping each other wirelessly, and so somehow are connected, when in wired backhaul - so a good switch detects this and enables loop protection.

I can't seriously have to disable loop protection to use a Deco? That really seems like no solution at all.

Anyone?

TP-Link

2021-02-03 01:07:16

Posts: 6831

Helpful: 3018

Solutions: 536

Stories: 28

Registered: 2018-07-23

Re:Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

2021-02-03 01:07:16

@NativeCanadian

Hi,

Thanks for your patience.

You are right and before the Ethernet finally created, the Deco units would remain wireless backhaul which would activate the Loop Prevention on TL-SG1016PE;

As for the available solution, currently, the best way might be to turn off the Loop Prevention on the switch temporarily and once the Ethernet backhaul is created, you could enable the Loop Prevention again.

Thank you very much and wait for your reply.

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!

jimmy_lin

LV1

2022-02-25 21:46:21

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2022-02-25

Re:Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

2022-02-25 21:46:21

@NativeCanadian

I have encountered simliar issue recently.

Mine is the latest firmware 1.5.0 build 20210121.

My setup is a little defferent.

I have the DECO in AP mode and connect to all my 3 DECO to a switch.

The northbound of the switch connects to a router.

router

swtch

+-----------------+--------------+

DECO DECO |

switch

+--------+----------+

DECO PC

The connection is fine initially. After some time (I am not sure how long it takes),

I notice the connection of the PC which is physical wired connected to a switch becomes very slow.

I notice that the upper switch detects a loop and shuts down the port which connects to the second switch.

In this case, the connection of the PC goes through the DECO wirelessly so the speed drops.

I don't have solution for the issue. I can only disconnect all the wire connection of the DECO.

I lose the backhaul connection benefit and I hope TP link can address this issue.

David-TP

2022-03-01 08:55:48

Posts: 12443

Helpful: 1716

Solutions: 1197

Stories: 9

Registered: 2020-04-14

Re:Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

2022-03-01 08:55:48

@jimmy_lin

Hi, Thank you for your feedback.

There hasn’t been a plan to change the current design that wireless backhaul will keep active until Ethernet backhaul is finally created yet.

May I know the model number of your network switch?

Have you tried the recommended suggestion: please turn off the Loop Prevention on the switch temporarily and once the Ethernet backhaul is created, you could enable the Loop Prevention again.

Thank you very much.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! Deco BE85_1.1.1 Supports WireGuard VPN,Channel Selection and Matter Deco BE65_V2_1.1.0 Supports WireGuard VPN, Channel Selection and More ▶Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.

Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

Deco x60 causes TP-link switch to enable loop protection in STAR connection pattern

Information

Voters 1

Tags