Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > Archer c6 ports are limited at 100 mbit/s

< Wi-Fi Routers

Archer c6 ports are limited at 100 mbit/s

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer c6 ports are limited at 100 mbit/s

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Inquisit0r

2021-01-19 16:12:18 - last edited 2022-06-23 06:17:01

Posts: 3

Helpful: 5

Solutions: 1

Stories: 0

Registered: 2021-01-19

Archer c6 ports are limited at 100 mbit/s

2021-01-19 16:12:18 - last edited 2022-06-23 06:17:01

Tags: #Highlighted Thread

Model: Archer C6

Hardware Version: V2

Firmware Version: 1.3.6

Hello,

I've seen many posts regarding this Archer c6 problem but none of them have a proper solution for it.

The problem is pretty much the same: the LAN ports are capped at 100 Mbit/s while the actual speed should be 400 Mbit/s.

Archer c6 is connected to the Vodafone router (model: Arris TG3442DE) which also has 4 Gbit LAN ports, and the Arris router is connected to an internet line.

When my laptop is connected with the cable (CAT 6) to the Arris router LAN port, the speed is around 370Mbit/s (which is accurate), but when I connect the laptop to the Archer c6 LAN port with the same (CAT 6) cable, it only shows 95-97 Mbit/s, no matter how many times I measure.

I tried this with both mods on Archer C6: access point, and router - the result is the same.

I also tried the instructions that were provided in the previous threads: in the router system settings the duplex is set to 1gbps; in my network adapter settings the duplex is set to full 1gbps; my network adapter is Realtek PCIe GbE Family Controller.

Attaching the screenshots as well. The laptop is connected to LAN port 3, it shows a 1Gbit full duplex, LAN ports 1 and 2 are offline (screenshot 1).

Thank you in advance for any solutions.

1 Accepted Solution

Inquisit0r

LV1

2021-02-22 12:44:19 - last edited 2021-02-23 01:07:21

Posts: 3

Helpful: 5

Solutions: 1

Stories: 0

Registered: 2021-01-19

Re:Archer c6 ports are limited at 100 mbit/s-Solution

2021-02-22 12:44:19 - last edited 2021-02-23 01:07:21

Thank you for your help @Ivaylo and @Kevin_Z.

The issue is resolved now.

To all users from Germany that use Vodafone internet provider with their default router (Arris TG3442DE in my case), in order to access 1GB\s speed on your second router (Archer c6 in my case) connected to the default router with CAT 6 cable, you need to do the following:

- register on their website (Mein Vodafone);

- go to settings -> internet settings and disable hotspot (it is activated by default);

- set up your second router in bridge mode (I used this tutorial);

- wait 7 days until the hotspot will be disabled (there is no way to do it faster).

And that's it. After my hotspot was disabled I got the speed I was looking for.

If this doesn't help you, then try to set up your default router in the bridge mode (mein vodafone > settings > internet settings > set bridge mode).

This thread can be closed, thank you.

Recommended Solution

6 Reply

terziyski

LV7

2021-01-19 22:16:39 - last edited 2021-01-19 22:20:08

Posts: 6971

Helpful: 5187

Solutions: 1125

Stories: 7

Registered: 2013-10-12

Re:Archer c6 ports are limited at 100 mbit/s

2021-01-19 22:16:39 - last edited 2021-01-19 22:20:08

@Inquisit0r

Are these screenshots from AP mode ? I supose you're using the C6 in AP mode.

If yes, would you check in Basic=>Network Map that the correct number of Wired/Wireless clients are reported by the device ?

I presume you don't have QoS configured at the moment.

There's no obviuos reason your internet connection to be limmited to 100 mbps, when the device port (LAN3) and your laptop's Realtek LAN adapter are connected @ 1 gbps.

The Internet port is also connected @ 1 gbps. (visible from the C6 interafce).

What if you set Duplex setting to: Auto negotioation. Does the C6 Internet port, LAN3 port or your laptop lan adapter speed change ?

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

Inquisit0r

LV1

2021-01-20 15:26:05

Posts: 3

Helpful: 5

Solutions: 1

Stories: 0

Registered: 2021-01-19

Re:Archer c6 ports are limited at 100 mbit/s

2021-01-20 15:26:05

@Ivaylo

The screenshots are done when the Archer C6 was in router mode.

Yes, QoS is off right now.

The wired and wireless device amount is correct too.

When the duplex is set to auto negotiation the LAN 3 port (laptop) shows 1000Mbit/s. Tried also other ports, they show 1000Mbit/s too, but the speed is still capped at 100Mbit/s.

I attached the screenshots from my Arris router (to which Archer c6 is connected), it also shows 1Gbit/s.

Do you recommend turning on QoS?

terziyski

LV7

2021-01-20 16:12:02 - last edited 2021-01-20 16:24:42

Posts: 6971

Helpful: 5187

Solutions: 1125

Stories: 7

Registered: 2013-10-12

Re:Archer c6 ports are limited at 100 mbit/s

2021-01-20 16:12:02 - last edited 2021-01-20 16:24:42

@Inquisit0r

Regarding QoS, I asked, because I thought if you have set some kind of a priority, it may causing that, but obviously you didn't.

For the following, I have meant in AP mode - "...would you check in Basic=>Network Map that the correct number of Wired/Wireless clients are reported by the device ? "

If the speeds on both C6 LAN3 and main router LAN are 1gbps then better leave it to Auto Negotioation.

Do you have another client device to test with, except that laptop and your mobile ? Actually, what's the speed if you test with the mobile and laptop (via C6 wireless ) ?

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".

Kevin_Z

2021-01-21 06:42:45

Posts: 21565

Helpful: 5027

Solutions: 2541

Stories: 21

Registered: 2018-12-24

Re:Archer c6 ports are limited at 100 mbit/s

2021-01-21 06:42:45

@Inquisit0r

Just to add, what if you try to reset the C6 to factory defaults by holding the reset button, then reconfigure it all over, leave all the settings by default, then test the speed again.

BTW, what is the length of the cable between the C6 and modem, how about that between the PC and C6? We understand that the cable between these devices should be all good, but we still suggest you try with new and shorter cables to see if it will make any difference.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Inquisit0r

LV1

2021-02-22 12:44:19 - last edited 2021-02-23 01:07:21

Posts: 3

Helpful: 5

Solutions: 1

Stories: 0

Registered: 2021-01-19

Re:Archer c6 ports are limited at 100 mbit/s-Solution

2021-02-22 12:44:19 - last edited 2021-02-23 01:07:21

Thank you for your help @Ivaylo and @Kevin_Z.

The issue is resolved now.

- register on their website (Mein Vodafone);

- go to settings -> internet settings and disable hotspot (it is activated by default);

- set up your second router in bridge mode (I used this tutorial);

- wait 7 days until the hotspot will be disabled (there is no way to do it faster).

And that's it. After my hotspot was disabled I got the speed I was looking for.

If this doesn't help you, then try to set up your default router in the bridge mode (mein vodafone > settings > internet settings > set bridge mode).

This thread can be closed, thank you.

Archer c6 ports are limited at 100 mbit/s

Archer c6 ports are limited at 100 mbit/s

Information

Voters 0

Tags