C6 and RE305 issue
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.C6 and RE305 issue
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Dear All,
I have a strange issue with my C6 and RE305.
Since i have from ISP Voip i must have ISP router connected to internet. So i connect C6 as router via Ethernet to ISP router and created a mesh with my RE305.
The first issue i have is that devices that are half a meter from C6 are connecting to RE305 that is on another floor. (this is really weird!!!)
Second issue i'm having and i was unable to find a solution is with my LG TV, TP-Link smart outlets and a shelly device (2.5).
- LG TV, after a few hours, wifi seems connected, but there is no traffic. Some times it is unable to connect to both 2.4 and 5 SSID's
- outlets and shelly, they loose connectivity to wifi
Both of the issues are fixed if i disable and re-enable C6 wifi. I connected the devices to my ISP wifi and there is no issue, so this is due to C6 or RE305
I already tried with static IP's, reservations, automatic IP;s, static channel on wifi but without any luck.
So: onemesh is not working as it should.. o have 7 devices close to the router, that are connecting to RE305 and not the router.
I'm thinking disabling onemesh, but this was the reason i choose those TP-Link products 
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Nice topology diagram !
How close are the ISP router and your C6 ? It is possible that issue has emerged due to a wireless interference between those two.
Have you tried to disable ISP router Wi-Fi and see if it persists.
Aside from that you are using C6 in router mode to benefit from OneMesh feature.
If you configure your C6 in pseudo AP mode you'll be avoiding double NAT in your network and still benefit from OneMesh.
- Copy Link
- Report Inappropriate Content
@Ivaylo Issue started with ISP router's wifi off ... later i enable it in order to have the devices connected.
I will try the pseudo-ap mode you suggested .. (dont know when though since my wife is also working from home).
I also saw a post for RE305 DHCP disable with beta firmware .. i will try this also...
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Ivaylo Changing it to AP mode though, will also disable QoS parental control ... I dont mind about parental, but QoS is something i need :(
- Copy Link
- Report Inappropriate Content
In this scenario the router is actually still in router mode. Just see the link I've sent - you won't be switching to AP mode through the WebGUI of the C6 (i.e. you'll still have the Parental control and QoS active). Keep in mind that in normal AP mode you can't use OneMesh, that's why I suggested the pseudo AP mode.
- Copy Link
- Report Inappropriate Content
@cakrit ok i will try that...
I try to upgrade RE305 with beta firmware that was proposed to disable DHCP... device is broken!!!!!!
Though make me realized something... Mesh working like crap!!!!!! all 2.4 devices were connecting to RE305 even if the router was next to them, they connected to RE305.
After RE305 died, no device connected to router 2.4 (all 5g devices connected) until i turned off and turned on again the 2.4 wifi.
So 100% the issue is with the 2.4 wifi of the router, (thats why all devices were connecting to RE305, because routers wifi is broken)...
So now i have one device broken and one with major issue on the 2.4 wifi
- Copy Link
- Report Inappropriate Content
Where did you get this beta FW for RE305 from - link ? Why do you think device broken, any LEDs lit/blinking when booting ? Was that FW for the same region and HW version as your RE305 ?
- Copy Link
- Report Inappropriate Content
From this forum: https://community.tp-link.com/en/home/forum/topic/192368?replyId=538000 checked the version and the firmware is V3 EU as my device https://static.tp-link.com/2020/202011/20201119/RE305_v3_201114.zip
all leds blink for 1-2 seconds and then nothing... i tried also reset
- Copy Link
- Report Inappropriate Content
Obviously it comes from a reputable source. I would suggest to wait until someone answers your issue before sending the device, if the service repair will last few weeks. It might be something easily fixable@home. How did you do the upgrade - via wireless or cable ?
Regarding your initial problem - did you have this 2.4 GHz band issue before introducing the new ISP router in your network ?
- Copy Link
- Report Inappropriate Content
@Ivaylo wireless but thats not the point.... device died on reboot ... so something was wrong with the firmware
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1787
Replies: 13
Voters 0
No one has voted for it yet.