Deco P9 set as main has 100% CPU load Vs. a Deco P7 that only use 20%
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello
I have a network composed by 3 Deco P7 and 3 Deco P9, in a 3 storey building.
Since I have recently purchased the 3 Deco P9 i have opted to use the new P9 as main DECO.
However anytime i use it as main its CPU load goes 100% and internet connectivity has so many flaws.
I'm forced now to use a Deco P7 as main deco as its CPU load is always around 20%.
Why the Deco P9 cannot function properly as main deco?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, thank you very much for your kind feedback.
And for anyone who had the same issue, there are some things that need to be mentioned first:
1. the High CPU usage as long as it dropped down to normal level after a refresh, would not be the cause of any issues;
so if there is no specific issue, like slow speed, ping spike/latency, or drops out, please don't worry;
2.While, if you noticed any drops out or high latency, the 100% CPU usage would be one phenomenon, again not the cause;
so you could provide some details about your current issue and leave me a message;
3. for the CPU to stay on a high level until a full reboot, it needs your attention as well and please feel free to leave me a message here;
thank you very much and wait for your reply.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Francesco81 I just bought the P9 and the CPU is showing 100CPU load too, let me know if there is a solution.
- Copy Link
- Report Inappropriate Content
I was hoping somebody from TpLink would have helped but no help in this tread.
I am using the P7 as main as the P9 is not performing well as main.
Beside the P7 of used as main has more feature such as antivirus and ddos
I'm very disappointed from tplink..
- Copy Link
- Report Inappropriate Content
Same issue here! 100% CPU load with log files showing loads of numerous erronious info.
For example the following error appears approximately every 3 seconds! "daemon.err /usr/bin/apsd: apsd_get_active_ports:214: Error: No such interface 27"
- Copy Link
- Report Inappropriate Content
Same issue here! 100% CPU load with log files showing loads of numerous erronious info.
- Copy Link
- Report Inappropriate Content
Hi, thank you very much for your kind feedback.
And for anyone who had the same issue, there are some things that need to be mentioned first:
1. the High CPU usage as long as it dropped down to normal level after a refresh, would not be the cause of any issues;
so if there is no specific issue, like slow speed, ping spike/latency, or drops out, please don't worry;
2.While, if you noticed any drops out or high latency, the 100% CPU usage would be one phenomenon, again not the cause;
so you could provide some details about your current issue and leave me a message;
3. for the CPU to stay on a high level until a full reboot, it needs your attention as well and please feel free to leave me a message here;
thank you very much and wait for your reply.
- Copy Link
- Report Inappropriate Content
@TP-Link I have done the upgrade but still many errors and warnings in the log. Also high cpu view
Thu Feb 11 13:16:22 2021 user.warn IMPROXY: WARNING[imp_verify_multicast_addr@206]: Group address ff02::2:ff08:d6fc is link-local multicast address
Thu Feb 11 13:16:22 2021 user.warn IMPROXY: WARNING[imp_verify_multicast_addr@206]: Group address ff02::2:ff08:d6fc is link-local multicast address
Thu Feb 11 13:17:01 2021 cron.info crond[15117]: crond: USER root pid 7505 cmd /sbin/qos_check
Thu Feb 11 13:17:01 2021 cron.info crond[15117]: crond: USER root pid 7506 cmd /sbin/pctl_log_update
Thu Feb 11 13:17:13 2021 user.warn IMPROXY: WARNING[mcast_recv_igmp@707]: Don't exist this VIF 15
Thu Feb 11 13:17:35 2021 user.warn IMPROXY: WARNING[mcast_recv_igmp@753]: Don't exist this Downstream VIF
Thu Feb 11 13:17:43 2021 user.notice IMPROXY: INFO[mcast_to_ex_hander@170]: Group
- Copy Link
- Report Inappropriate Content
I noticed the same issue and updated the firmware as suggested. The CPU load is still 100%.
Note that I got a brand new P9 today and run immediately into this problem.
Please let me know if there is something I can do to help debug.
- Copy Link
- Report Inappropriate Content
@Stickelbilly any response from TP-link?
- Copy Link
- Report Inappropriate Content
@TP-Link Hello Did you find a solution?
I have the same problem the cpu is 100% is I have latencies even my network to wire!
I updated my P9s with the "p9-SP1-up-ver1-1-3-P1 [20210115-rel60510] _debug.bin" always the same problem :(
Helped me I have 6 Deco P9 (but two are still in the box) do you have an idea or a lead ??
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 8512
Replies: 25
Voters 0
No one has voted for it yet.