Wifi security WPA2 AES missing in Deco M9 Plus?
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
I am trying to connect my car ( Volvo XC60 ) to my Wifi. The car wants me to change WPA2 to AES instead of TKIP!
So no connection!
Connection to another Wifi router with WPA2 AES is OK!
I can not find any place in the Deco M9 settings to change Wifi security!
Any clues??
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Thanks very much for the update. Sorry to hear that the Dahua camera cannot connect to the WPA2-PSK (AES) wireless network.
BTW, may I have its model? Thanks.
- Copy Link
- Report Inappropriate Content
Hi,
This is the device:
Device Type IPC-HFW1320S-W
System Version 2.400.0000000.16.R, Build Date: 2017-08-31
WEB Version 3.2.1.490211
ONVIF Version 16.12(V2.3.1.458331)
Copyright 2017, all rights reserved.
Best Regards
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hello, do you mean Deco M4R? You can install the beta firmware for the Deco M4, they are the same:
https://community.tp-link.com/en/home/forum/topic/227662
Thanks.
- Copy Link
- Report Inappropriate Content
Thanks so much for your info. Sorry that you may need to plug it into the Deco with a cable or change the security back to the mixed WPA2-PSK (AES)+WPA-PSK (TKIP).
Cretu wrote
Hi,
This is the device:
Device Type IPC-HFW1320S-W
System Version 2.400.0000000.16.R, Build Date: 2017-08-31
WEB Version 3.2.1.490211
ONVIF Version 16.12(V2.3.1.458331)
Copyright 2017, all rights reserved.
Best Regards
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I had the same issue with two Amcrest WiFi camreas. It looks like even though they were capable of connecting to AES only, since they had originally connected as TKIP they would only reconnect to TKIP. Luckily I have another router in my network that I could connect them to. What I had to do was switch the Deco back to TKIP which allowed the cameras to reconnect. I then logged into them and connected them to the other WiFi SSID, switched the Deco back to AES only, and then I could switch the cameras back over to the Deco.
- Copy Link
- Report Inappropriate Content
Hi, yes, please get the beta firmware for E4 from the below link:
https://community.tp-link.com/en/home/forum/topic/227662?page=1
- Copy Link
- Report Inappropriate Content
Hello,
May I also have the model number of your two Amcrest WiFi cameras?
What does this sentence mean "switched the Deco back to AES only, and then I could switch the cameras back over to the Deco."?
AlanF wrote
I had the same issue with two Amcrest WiFi camreas. It looks like even though they were capable of connecting to AES only, since they had originally connected as TKIP they would only reconnect to TKIP. Luckily I have another router in my network that I could connect them to. What I had to do was switch the Deco back to TKIP which allowed the cameras to reconnect. I then logged into them and connected them to the other WiFi SSID, switched the Deco back to AES only, and then I could switch the cameras back over to the Deco.
- Copy Link
- Report Inappropriate Content
I'm able to connect to the camera, I tried another Ssid, also tried adding manually with the same result.
Being just one device from 30 :) it's OK, switched to cable.
I think in my case the camera is just a little retarded 😂 because I have an ethernet cable connected but I can access the device on both IPs eth and wlan... even if wlan is off.
Maybe instead of just a simple link to all available firmwares you should keep the "best solution page" and just add all the links.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 20
Views: 63024
Replies: 157
Voters 19
