Home Network Community > Deco > Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes
< Deco

Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes
Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes
2020-03-25 16:30:14
Model: Deco M9 Plus  
Hardware Version: V1
Firmware Version: 1.3.0

Our network has been up for a month with all three decos online and everything working well. We have a computer that will not connect as of this morning. It is a Win 10 HP laptop. When you try to reconnect it has the normal messages and it completes the network connection steps without any error messages but it has "no internet" listed on the connection. Its an odd state because if there is no Internet then what is it connected to? Has anyone seen this before? All other devices - about 30 of them - are connecting and working fine. Any help you can provide is greatly appreciated.

  0      
 
  0      
 
#1
Options
3 Reply
Re:Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes
2020-03-26 02:37:26

@Mamie 

 

Hi, with this Windows 10 HP laptop connected to the Deco's wifi, please click here to verify whether it obtains valid IP address and gateway from Deco. 

 

And please ensure that you have not added this device into blacklist or parental control settings. 

 

You can try to ping the gateway of Deco which is 192.168.68.1 by default and show me the results. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes
2020-03-26 11:54:01

@Kevin_Z  thank you, we went to try your suggestions and now the computer is connecting through to the network. Yesterday it was saying it was connected to the network but not to the internet. How do I remove parental controls? I wasn't sure how to configure this during setup so I put adult for the highest level of access and I did it by user. How do I remove users from that list or do I need to? No one is blacklisted.

  0  
  0  
#3
Options
Re:Windows 10 HP laptop has stopped getting an Internet connection but the connection request completes
2020-03-27 02:39:05

@Mamie 

 

You can open Deco app and go to the Parental Control page and you will see the profile you have created. You can swipe it to the left to delete it or hold it for a few seconds to reset. (It varies due to the OS of cellphone).

 

Below is the instruction to set it up: https://www.tp-link.com/support/faq/1598/

 

And right now, with your computer connected to the Deco, can you access internet? If it is still the same, try to reboot the computer or update the driver of the network adapter. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 759

Replies: 3

Related Articles
 HP Laptop Windows 10 Connection Problem with Deco E4
1518 0
wi-fi network not secure in windows 10
2610 0
 Deco M9, HP laptop will not connect to WIFI
2846 0
Deco M5 blocking Microsoft on Windows 10 laptop
2711 1
TP-Link Utility for Windows 10 stopped working
15305 0
Can't seem to update Windows 10 on Deco Mesh wi-fi
1403 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.