Home Network Community > Deco > Unstable network
< Deco

Unstable network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Unstable network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Unstable network
Unstable network
2020-03-06 20:34:28
Model: Deco E4  
Hardware Version:
Firmware Version:

Cannot get clue on Deco setup and have very unstable network. I have lan cable as input to my apartment, this cable connected to main deco unit then direct cable to other part of house where slave is located, PC connected to slave with a cable. it is not so far like 10m, but there are no line of sight and major concrete wall enroute. I have 2 Android TV and lot of smart bulbs/sockets, etc sometimes up to 30 devices online.

So problems: 

1. Slave reporting that it connected on wireless while cable plugged in.

2. Deco app isn't able to connect to system while overhaul cable connected, when cable disconnected I can connect to system.

3. Often network dropped, mobile stuck on "obtaining ip address" and nothing is working

4. Often wan drop, main deco blinks red, then slave start blinking red. Attached log of such incident.

File:
log-2020-03-05.log (3).txtDownload
  0      
 
  0      
 
#1
Options
6 Reply
Re:Unstable network
2020-03-09 02:55:52

@Mapper 

 

Hello, we need get some information first so that we can do further analysis and figure it out. 

 

1. The current network diagram. Especially how do you connect the slave Deco to the main Deco. Is there a cable from main Deco to the slave Deco directly, or there is a wall socket in between?

 

2. When Deco stops working, have you ever tried to connect your computer to the main Deco/cable directly and test whether it works? 

 

3. You can swap the locations of the Deco units or change the slave Deco to the main Deco.

https://www.tp-link.com/support/faq/2400/ 

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Unstable network
2020-03-09 08:18:28

@Kevin_Z 

1. Nothing in between, direct cable, no wall socket

2. No, I don't, there is no possibility to do so.

3. I will try when I get home.

More observation:

When I disconnect bachaul cable on Thursday evening network was more or less stable during weekend. No wan dropping, no red lights blinking. Hovewer latancy on devices connected to slave is awfull most of time. Probably this is because of slave position and not working cable backhaul.

  0  
  0  
#3
Options
Re:Unstable network
2020-03-10 02:43:23

@Mapper 

 

Thanks for your reply. 

 

Generally speaking, the wired connection is more stable than wifi connection, it is normal that the latency of wifi connection will be higher than wired connection. 

 

You can change another ethernet cable to connect the slave Deco and main Deco, like cat 5e or above. And please confirm whether you can access internet from the WAN cable (internet source) directly when the Deco stops working.

 

Besides, take your time to test the performance after you swap the location or change the slave Deco to main Deco. 

 

Any updates, be free to let us know. 

 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Unstable network
2020-03-17 18:09:47

@Kevin_Z 

Okay, so I switched places master and slave, and did connect them with a cable again. Generally speaking situation is same. After they are booted up, slave shows that it's connected over wifi while cable is in place, after some minutes app isn't able to get any info and kicking me off to "we couldn't find deco". So it behaves exactly same way it was before. Neither I am able to get to web site to download log.

  0  
  0  
#5
Options
Re:Unstable network
2020-03-17 18:18:15

I've disconnected cable and there are bunch of "unable to connect to 192.168.1.100"  (see attached log)

File:
log-2020-03-17.log.txtDownload
  0  
  0  
#6
Options
Re:Unstable network
2020-03-17 18:41:42

So I got them together and link with a patch cord. Situation is same Ethernet backhaul isn't working and after couple of minutes application kicked me off.

  0  
  0  
#7
Options

Information

Helpful: 0

Views: 1124

Replies: 6

Related Articles
Unstable DECO network
1165 0
 network unstable
465 2
 The network is unstable.
3023 0
 Deco E4 unstable
230 0
 Unstable WIFI Network
489 0
 Very Unstable network Connection
254 1
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.