Deco M4 - speed capped at 100Mbps
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi
I've been using Deco M4 since 5 months.
The setup was:
Broadband modem ==> Deco M4 1st unit ==> Deco M4 2nd unit.
Earlier my broadband was only 100Mbps and later I've upgraded it to 200Mbps.
My broadband modem and Deco M4 1st unit is connected using a Cat 6 ethernet cable. But still the maximum speed I'm receiving is capped at 100Mbps via Deco.
When I directly connect to my broadband modem then I'm receiving speeds upto 200Mbps.
Followed the troubleshooting steps on Deco but it didn't help!
Thanks
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
I have 3 Deco m4 on my house.
For the last month everything was just great 1000/200 on speeetest. But today i am getting 94/94.... this is very annoying because this device is not cheap and it looks to have a lot of problems.
I rebooted a lot of times and nothing changes.
Please someome help me fix this
- Copy Link
- Report Inappropriate Content
For me it works after latest update 1.5.0 20210511 Rel 344580
It is 3 months already and there is no problem with the speed
- Copy Link
- Report Inappropriate Content
@Grzegorz_S Hi. I have the same issue and i did not find any fix. How did you get the firmware 1.5? I am in Thailand. My current firmware is
| 1.4.3 Build 20200918 Rel. 74289 |
Whenver i check for an update in the app is says if the latest...also i cannot find 1.5 on tp-link website.
- Copy Link
- Report Inappropriate Content
@TP-Link Is there an official fix already? I have the same problem...Some users got the firmware 1.5. Mi deco`s are still on 1.43 since many months and it always says they are up to date. How can i fix this????
My 3 Deco`s are M4R v2.0 . All of the 1.4.3 Build 20200918 Rel. 74289
Wifi works at maximum speed (300mbs). Wired is limited to 100mbs.
- Copy Link
- Report Inappropriate Content
Hi, firmware 1.5.0 has been withdrawn from official websites for further optimization.
Currently, 1.4.3 build 20200918 is the latest firmware for Deco M4 v1/v2.
As for your current issue” Wi-Fi works at maximum speed (300mbs). Wired is limited to 100mbs.”, they might be three possibilities:
1. the port rate on Deco dropped to 100m/s.
2. the Ethernet cable is only up to 100m/s.
3. the Ethernet adapter of the tested laptop is only up to 100m/s.
In case It is the last two issues, please test with a different laptop with a brand new cat6/7 cable.
After that, if the issue still existed, please send an email to support.forum@tp-link.com about your current issue.
- Copy Link
- Report Inappropriate Content
I checked again and unfortunatelly it doesn't work again :(
Even after rebooting all devices.
Also I did a test. I set QoS to 50 (download) / 10 (upload) Mb/s, did a reboot and test the speed (my Internet is 600/50).
Result: 94 / 50
Any thoughs?
- Copy Link
- Report Inappropriate Content
Hi, have you tried the beta firmware here to see whether it helped or not:
[Solution] Wi-Fi speed drops down after updating Deco M4 to the latest 1.5.0 firmware
- Copy Link
- Report Inappropriate Content
I am having the exact same problem. My 3 pack deco M4R V3 running 1.5.1 Build 20210512 Rel. 39021 caps at 100 mbps even though my ISP service speed is 300mbps. Checked the 300mbps speeds connecting lan to my laptop directly. However, over deco the speed is capped at 90-100 mbps. Please help me.
- Copy Link
- Report Inappropriate Content
@PavanKumar try to put the operation mode of M4 from Router to Access Point, it works for me, i have a 1gbps broadband connection and the M4 in Router lode only gave me 200Mbps, but with that change, gave me 600Mbps-700Mbps
- Copy Link
- Report Inappropriate Content
@Aravind21 try to put the operation mode of M4 from Router to Access Point, it works for me, i have a 1gbps broadband connection and the M4 in Router lode only gave me 200Mbps, but with that change, gave me 600Mbps-700Mbps
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 54429
Replies: 56
Voters 0
No one has voted for it yet.