Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > How can I manually change default deco network map?

< Deco

How can I manually change default deco network map?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How can I manually change default deco network map?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

mrboxxy

2020-01-14 01:37:10

Posts: 1

Helpful: 3

Solutions: 0

Stories: 0

Registered: 2020-01-14

How can I manually change default deco network map?

2020-01-14 01:37:10

Model: Deco M5

Hardware Version:

Firmware Version: 1.4.0

Hello,

I have set up the 3 decos M5 in router mode. Problem is that there were no improvements in terms of speed. I have a 3 story house with the main deco on the first floor, at the same place my router was, and the other two on the second and third floors.

The "optimized" mapping is sub-par as it links both decos to my main deco instead of having my third floor deco linked to the second floor deco.

Current network mapping:

Instead, I want it as advertised here:

How can I achieve this?

Thank you

2 Reply

RedRoger

LV2

2020-01-14 06:32:40 - last edited 2020-01-14 06:34:02

Posts: 72

Helpful: 26

Solutions: 2

Stories: 0

Registered: 2019-07-24

Re:How can I manually change default deco network map?

2020-01-14 06:32:40 - last edited 2020-01-14 06:34:02

@mrboxxy your desired configuration as on picture supposes using of another router with all three decos in AP mode as I understand. If you want to use your Decos in Router mode, then for your purpose AS FOR ME it is better to use a switch and connect all your decos by ethernet. At least I did so at my home :). Then both your additional Decos will get traffic from the main one on maximum speed. If you use WiFi connection between Decos, there are no ways to say how and from which Deco they should get the traffic - they will choose somehow, maybe and the most likely by signal strength....

Kevin_Z

2020-01-22 02:10:03

Posts: 21573

Helpful: 5034

Solutions: 2542

Stories: 21

Registered: 2018-12-24

Re:How can I manually change default deco network map?

2020-01-22 02:10:03

@mrboxxy

Hello, there is no option to force the front-end device yet; while it seems that the signal strength got from the main Deco does not reach the threshold value, that is why it does not trigger the AP/Band steering, and the third Deco connects to the main Deco, not the second one.

First, you can move them further away between each other, and you can disable the main Deco and ensure that the third Deco connects to the second one, and then you can turn on the main Deco.

May it help.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

How can I manually change default deco network map?

How can I manually change default deco network map?

Information

Voters 0

Tags