Home Network Community > Wi-Fi Routers > ssh, telnet, upnp on Archer C2 router
< Wi-Fi Routers

ssh, telnet, upnp on Archer C2 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ssh, telnet, upnp on Archer C2 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
ssh, telnet, upnp on Archer C2 router
ssh, telnet, upnp on Archer C2 router
2020-01-11 12:26:39
Model: Archer C2  
Hardware Version: V1
Firmware Version: 0.9.1 5.0 v0032.0 Build 170207 Rel.49213n

Hi

 

I have an Archer C2 750 router. I ran nmap  192.168.0.1 from my computer and it reported that these are available :

 

22/tcp   open  ssh
23/tcp   open  telnet
80/tcp   open  http
1900/tcp open  upnp

 

I wasn't able to ssh into it, the following link states that its for use with an app only, no login. is that correct?

https://forum.lowyat.net/topic/4282635/all

 

Can I shutdown or limit telnet? I was able to limit login over http to one computer on the local network, didn't affect telnet which was still accessable by others.

 

What is upnp for? I switched off upnp via admin webpage and nmap reports service ir running (or port is open anyway)

 

Thanks,

Rob

  0      
 
  0      
 
#1
Options
2 Reply
Re:ssh, telnet, upnp on Archer C2 router
2020-01-14 11:12:02

@robdavies 

 

Hello, the Archer C2 supports Tether app, and the app uses SSH22. You can read this article. https://www.tp-link.com/support/faq/2462/

 

The Archer C2 has the built-in web management page, which uses http port 80. 

 

The UPnP (Universal Plug and Play) protocol allows the applications or host devices to automatically find the front-end NAT device and send request to it to open the corresponding ports.

 

While for the telnet, as far as I know, it is disabled by default; we can access the web UI with the local login only; you can try to use telnet to access the router to rule out the flaw of nmap software. 

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:ssh, telnet, upnp on Archer C2 router
2020-01-27 18:43:56

@Kevin_Z 

 

Thank you very much for replying, just realised I hadn't replied myself.

 

Yes, it covers it all. Telnet it accessable from this model, thankfully only from LAN. I did a scan from at home and those ports showed up, panic on. It wasn't until after I posted I did a scan from a friends house an nothing showed up. So with your great explanation, panic off.

 

Thank you again,

rob

 

  0  
  0  
#3
Options

Information

Helpful: 0

Views: 9419

Replies: 2

Related Articles
Howto replace the antenna on the TP-Link Archer C2 - Router
3042 0
SSH or Telnet on TP-Link Archer C5 v2
1373 0
[resolved] VPN sur ARCHER C2
927 0
How to set full duplex on Archer C2?
5719 0
 Connect to router via ssh or telnet
2734 0
 Archer MR200 SSH and TELNET disable
1141 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.