Home Network Community > Deco > Deco P7, manually select signal source?
< Deco

Deco P7, manually select signal source?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco P7, manually select signal source?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco P7, manually select signal source?
Deco P7, manually select signal source?
2019-12-31 16:35:36 - last edited 2020-02-24 11:17:22
Model: Deco P7  
Hardware Version:
Firmware Version: 1.3.1

I have five Deco P7 units in my house. The main Deco unit and 3 others are connected via ethernet cable, one Deco unit is connected via Wifi.

That one Wifi unit, i will call it the "remote deco" because of its location, has a really poor Wifi connection to the main unit which is 17 meters (two walls) away, although there is another deco unit at 7 meters (one wall) which should provide a much better wifi connection to the "remote deco". But the "remote deco" just won't connect to it.

 

Also, although the powerline adapter shows a "greenish" color occasionally, it seems "somewhat orange" at the moment (please use better distinguishable colors in the future). I have no clue about the quality of the powerline connection, there isn't any info about it in the app. All Deco's are directly connected to the same power system (we only have one phase).

I removed and reinstalled the "remote deco" two times, no success.

I disabled beamforming, no success.

 

I want that "remote Deco" to connect to the nearest Deco unit, but i can't force it. Also i would like to force Powerline, but i can't.

 

Should a Deco unit be able to connect to any other Deco unit which isn't the "main" unit? That's the whole idea of a Mesh network right?

 

Please help.

 

 

  1      
 
  1      
 
#1
Options
1 Accepted Solution
Re:Deco P7, manually select signal source?-Solution
2020-01-02 02:40:52 - last edited 2020-02-24 11:17:22

@AM1 

 

Hello, to fix the signal source is not supported by Deco series product yet, while we do have some similar feedbacks and we have forwarded to our product department; they will evaluate the feasibility. 

 

Back to your case, the slave Deco can be connected to the other slave Deco or main Deco in the same mesh network as designed; it seems that the signal strength obtained from the main Deco does not reach the threshold value which failed to trigger AP steering; you can move them farther away from each other; or you can reboot the remote Deco to give it a go; And you can turn off  the main Deco first and make remote Deco connect to other Deco nodes and turn on the main one. 

 

For the powerline backhaul, it shows orange means that the powerline rate is slow which affects the performance; you can change another wall socket to plug the Deco P7. 

 

Besides, we would keep working on it and try to make it more convenient and easier. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
6 Reply
Re:Deco P7, manually select signal source?-Solution
2020-01-02 02:40:52 - last edited 2020-02-24 11:17:22

@AM1 

 

Hello, to fix the signal source is not supported by Deco series product yet, while we do have some similar feedbacks and we have forwarded to our product department; they will evaluate the feasibility. 

 

Back to your case, the slave Deco can be connected to the other slave Deco or main Deco in the same mesh network as designed; it seems that the signal strength obtained from the main Deco does not reach the threshold value which failed to trigger AP steering; you can move them farther away from each other; or you can reboot the remote Deco to give it a go; And you can turn off  the main Deco first and make remote Deco connect to other Deco nodes and turn on the main one. 

 

For the powerline backhaul, it shows orange means that the powerline rate is slow which affects the performance; you can change another wall socket to plug the Deco P7. 

 

Besides, we would keep working on it and try to make it more convenient and easier. 

 

Good day. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
Re:Deco P7, manually select signal source?
2020-06-22 02:57:59

@Kevin_Z 

This issue was reported at least a year ago perhaps more.

Are you ever going to fix this?

Tp link Deco as it is, is NOT a true mesh product.

  3  
  3  
#3
Options
Re:Deco P7, manually select signal source?
2020-08-19 17:32:46

@AM1 I have the same issue, I just noticed that the "mesh" is not truly a mesh, all repeaters connect to the main deco which is an issue if the main deco is on one side of the house. My concern is that this has been reported for a while now with no resolution. I'm also considering changing to another company's solution if this doesn't get fixed soon.

  3  
  3  
#4
Options
Re:Deco P7, manually select signal source?
2020-08-30 18:32:28
Same issue with the M5, just rebooted the furthest disc and it's connected to the middle disc.. thankfully!
  0  
  0  
#5
Options
Re:Deco P7, manually select signal source?
2021-01-15 17:59:33

@Greenones 

 

mine Deco M9 Plus also facing this problem. 

  1  
  1  
#6
Options
Re:Deco P7, manually select signal source?
2021-04-05 14:24:22

@poyojorak 

 

I have the similar issue.  I have a remote office and have a printer in there .    I have a M9 unit in the office connected over powerline and the printer only connects to the unit indoors which is so far away the signal is very iffy.   

 

Poor design if you can't reselect the wireless repeater closest to the device.

 

@TP-Link Will you enable this feature ?

  3  
  3  
#7
Options

Information

Helpful: 1

Views: 4556

Replies: 6

Related Articles
Deco M4 select signal source
20670 9
Deco M9 select source signal
16671 5
X60 Deco select signal source / signaalbron
4143 0
How can I select manual signal source on Deco M4 (v2)
599 0
 Deco M4 select signal source
1160 0
 Deco e4 select signal source
483 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.