Home Network Community > Wi-Fi Routers > How to activate bridge mode on Archer C6
< Wi-Fi Routers

How to activate bridge mode on Archer C6

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to activate bridge mode on Archer C6

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to activate bridge mode on Archer C6
How to activate bridge mode on Archer C6
2019-12-17 18:47:40 - last edited 2021-09-03 01:16:28
Model: Archer C6  
Hardware Version: V2
Firmware Version: 1.1.0

Hello all,

 

I have bought an Archer C6 router in Amazon in order to extend my network provider wifi due to in some rooms of my house I have a low wifi...

 

My problem is that I don't find WDS Bridge mode so I have performed an access point mode, that is a temporaly solution cause I have to turn off and turn on every time I move over my house...

 

I don't know if is it explained properly.

 

I suspect that Archer C6 is not compatible with that mode so I have to buy another model.

 

Thanks in advance,

Best regards.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:How to activate bridge mode on Archer C6-Solution
2019-12-18 05:57:29 - last edited 2021-09-03 01:16:28

@SamuelBG 

 

Archer C6 supports WDS bridging function. Below is the instruction to set it up. 

https://www.tp-link.com/support/faq/1555/

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  1  
  1  
#2
Options
2 Reply
Re:How to activate bridge mode on Archer C6-Solution
2019-12-18 05:57:29 - last edited 2021-09-03 01:16:28

@SamuelBG 

 

Archer C6 supports WDS bridging function. Below is the instruction to set it up. 

https://www.tp-link.com/support/faq/1555/

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  1  
  1  
#2
Options
Re:How to activate bridge mode on Archer C6
2020-04-19 10:12:45 - last edited 2020-04-19 10:17:17

@SamuelBG 


If You cannot find WDS check if:

 

  1. Operation Mode is set to Router (not Access Point).
  2. WDS is enabled in advanced options -> system tools -> system parameters.

 

Cheers!

  2  
  2  
#7
Options

Information

Helpful: 0

Views: 58890

Replies: 2

Related Articles
 How to activate WDS or Wireless Bridge mode in Archer AC5400?
1751 0
 problem with vpn using pppoe mode on Archer C6 and isp mode bridge
615 0
Using a pair of Archer C6 to build a WDS wireless bridge
2651 0
Archer c6 ONEMESH with RE305 AP MODE
1083 0
Archer C6 as a repeater for Archer C6
81809 2
Archer C6 v2 not working in access point mode
1909 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.