Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Green light and correct setup yet no wifi signal

< Deco

Green light and correct setup yet no wifi signal

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Green light and correct setup yet no wifi signal

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Erica1

2019-12-14 23:18:14

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-12-14

Green light and correct setup yet no wifi signal

2019-12-14 23:18:14

Model: Deco M5

Hardware Version:

Firmware Version: Current up to date

I have 3 decos. 2 work perfectly.

The 3rd can be set up using bluetooth only. It is not detected when using wifi setup. However once set up the light is green and customer service says it's in perfect working order. However it is not. Despite the green light and the fact that it appears on the app as a connected deco, it does not transmit wifi. When scanning devices to find a wifi signal there is none in its range. Also customer support insisted that the problem is due to the fact that this deco is too far from the main deco. This cannot be the case - I've tested it myself by swapping decos...and it works...meaning that this particular deco is faulty. However I gave it to the service centre and they sent it back saying it's in perfect working order

5 Reply

Kevin_Z

2019-12-16 07:59:49

Posts: 21782

Helpful: 5151

Solutions: 2575

Stories: 21

Registered: 2018-12-24

Re:Green light and correct setup yet no wifi signal

2019-12-16 07:59:49

@Erica1

Try to turn off the other two Decos which work properly; After that, please verify whether you can detect any TP-Link Deco wifi networks with your device when the 3rd Deco powered on.

Besides, you can connect your computer to it by wired cable and verify whether you can get internet; and you can click here to get the IP address and gateway.

Considering service center said it works well, you can hard reset it by holding the reset hole for 1s and reconfigure it.

May it help.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

vickyc

LV1

2020-06-13 12:00:19

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2020-06-13

Re:Green light and correct setup yet no wifi signal

2020-06-13 12:00:19

@Erica1 I am having a very similar issue with a brand new Deco M5. Any luck with your issue?

My Deco is updated to the latest firmware (1.4.4). Funny thing is, it worked fine for a few hours, now the Wifi signal is very weak and barely (if ever) manages to connect even when my phone is right next to the unit. If I move a few steps away the network is not even visible. Also, when I run the internet test from within the Deco, it returns normal results. So only the wireless network itself isn't working.

Also tried moving the Deco far from other devices to reduce interference, but no luck. Think I'm gonna have to return it and get a different router :(

unoh07

LV1

2021-09-21 16:19:49

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-09-21

Re:Green light and correct setup yet no wifi signal

2021-09-21 16:19:49

Hi, I am also encountering this with one of my deco m5 units. can only be setup via Bluetooth, when setup as main router - the wifi network is not detected. shows green light and connected via the deco app.

Hope someone has found a solution. Thanks!