Home

Forums

Stories

Knowledge Base

Home Network Community > Powerline Adapters > Power Line adapter - Master Slave?

< Powerline Adapters

Power Line adapter - Master Slave?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Power Line adapter - Master Slave?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

PyroGer101

2019-12-03 00:44:37 - last edited 2019-12-05 07:29:03

Posts: 2

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2019-12-03

Power Line adapter - Master Slave?

2019-12-03 00:44:37 - last edited 2019-12-05 07:29:03

Model: TL-PA9020P KIT

Hardware Version: V3

Firmware Version: 3.2.4_902113_180511_904

Hi all,

I have recently purchased 4x TL-PA9020P and have them connected to 4x Google Wifi APs (1x AP is set as router and others are APs only).

Currentl looks like this:

ISP Router (bridge mode)
>>> Google AP (Router Mode)
>>> 8 Port Switch
>>> No.1 TL-PA9020P (Primary)
- >> No.2 TL-PA9020P >> Google AP
- >> No.3 TL-PA9020P >> Google AP
- >> No.4 TL-PA9020P >> Google AP

What confuses me is when I look at tpPLC and it shows me the topology it shows me that No.4 TL-PA9020P is the primary communicating out to 1,2 and 3.

The only logic I can think of (because the primary appears to change around on tpPLC) is that tpPLC is drawing a map based on my laptops current path of connectivity. If that is the case that would make sense but otherwise I would of expected to see No.1 being the primary and has arrows pointing to all the other power line adapter (2,3 and 4).

So Question no.1 is that correct? Is the tpPLC mapping by route traversed? If it is not correct how do I mark the No.1 TLPA9020P to be the "Primary"/ Master.

Question no.2 which I also think I know the answer for but seeing as these devices are MIMO should I have two network links coming in from my switch into my first "primary" TL-PA9020P or is that going to create a loop?

Thanks,

Ger

1 Accepted Solution

Kevin_Z

2019-12-03 08:03:05 - last edited 2019-12-05 07:29:03

Posts: 21569

Helpful: 5032

Solutions: 2542

Stories: 21

Registered: 2018-12-24

Re:Power Line adapter - Master Slave?-Solution

2019-12-03 08:03:05 - last edited 2019-12-05 07:29:03

@PyroGer101

The powerline adapter which you connect your computer to will be recognized as the master unit on the utility; if you connect your computer to the switch or the router, then the powerline adapter detected by the utility is the master unit through the interactions.

You can rename these powerline adapters to distinguish them if you use your computer only.

For the second question, MIMO is short for Multiple-in-Multiple-out, it is a feature which is enabled by default; we do not have to and cannot connect the primary powerline adapter to the switch with 2 ethernet cables.

May it help.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Power Line adapter - Master Slave?

Power Line adapter - Master Slave?

Information

Voters 0

Tags