Home Network Community >
DSL Modem Routers >
ADSL Modem TD-W8951 ND V1 bricked while updating firmware
ADSL Modem TD-W8951 ND V1 bricked while updating firmware
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.ADSL Modem TD-W8951 ND V1 bricked while updating firmware
Posts: 3
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
2012-12-29 18:17:56
Posts: 3
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
ADSL Modem TD-W8951 ND V1 bricked while updating firmware
2012-12-29 18:17:56
Tags:
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : TD-W8951ND_V1_100728
ISP : B.S.N.L
While i was trying to update firmware of the device,it got bricked.
Even i have followed all the instructions for updating Firmware.
Please Reply.
Thanks.
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : TD-W8951ND_V1_100728
ISP : B.S.N.L
While i was trying to update firmware of the device,it got bricked.
Even i have followed all the instructions for updating Firmware.
Please Reply.
Thanks.
#1
Options
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Thread Manage
Announcement Manage
6 Reply
Posts: 8
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
Re:ADSL Modem TD-W8951 ND V1 bricked while updating firmware
2012-12-30 00:16:09
Hi:
try to configure your network card with static ip address, 192.168.1.2 netmask 255.255.255.0 default gateway 192.168.1.1
Once you are done, connect directly your computer by cable to the router (not wifi) and try to ping 192.168.1.1, if the router is still alive, try to see if it is still responding to the port 21 (netcat or telnet should do the work, nc 192.168.1.1 21 or telnet 192.168.1.1 21). If you are lucky and your router is still alive, connect via tftp, set the binary mode by default and send the firmware again.
try to configure your network card with static ip address, 192.168.1.2 netmask 255.255.255.0 default gateway 192.168.1.1
Once you are done, connect directly your computer by cable to the router (not wifi) and try to ping 192.168.1.1, if the router is still alive, try to see if it is still responding to the port 21 (netcat or telnet should do the work, nc 192.168.1.1 21 or telnet 192.168.1.1 21). If you are lucky and your router is still alive, connect via tftp, set the binary mode by default and send the firmware again.
mann wrote
Region : India
Model : TD-W8951ND
Hardware Version : V1
Firmware Version : TD-W8951ND_V1_100728
ISP : B.S.N.L
While i was trying to update firmware of the device,it got bricked.
Even i have followed all the instructions for updating Firmware.
Please Reply.
Thanks.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#2
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 3
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
Nothing Works
2012-12-30 10:49:32
mtruchado wrote
Hi:
try to configure your network card with static ip address, 192.168.1.2 netmask 255.255.255.0 default gateway 192.168.1.1
Once you are done, connect directly your computer by cable to the router (not wifi) and try to ping 192.168.1.1, if the router is still alive, try to see if it is still responding to the port 21 (netcat or telnet should do the work, nc 192.168.1.1 21 or telnet 192.168.1.1 21). If you are lucky and your router is still alive, connect via tftp, set the binary mode by default and send the firmware again.
Hi
First of all Thanks for Reply.
I changed network ip settings to manual and provided it with following
IP Address-192.168.1.2
Subnet Mask-255.255.255.0
Default Gateway-192.168.1.1
then i tried to ping the modem/router,it says Destination Host Unreachable and thus no other command is applicable yet.
Thanks.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#3
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 862
Helpful: 7
Solutions: 1
Stories: 0
Registered: 2012-11-05
Re:ADSL Modem TD-W8951 ND V1 bricked while updating firmware
2012-12-30 13:30:13
Change it back into obtain IP address automatically and check default gateway of local area connection.
If nothing, try to hard reset it (holding reset hole about 15 secs) and see what happens. Check status of all indicators and confirm they are runing properly.
If nothing, try to hard reset it (holding reset hole about 15 secs) and see what happens. Check status of all indicators and confirm they are runing properly.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#4
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 3
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
Re:ADSL Modem TD-W8951 ND V1 bricked while updating firmware
2012-12-30 14:00:12
Even 30-30-30 Hard reset does'nt work at all.
Only power LED glows.
Only power LED glows.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#5
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 8
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
Re:ADSL Modem TD-W8951 ND V1 bricked while updating firmware
2012-12-31 01:20:21
Hi
I don't think that configuring your network card as a "obtain IP address automatically" is going to work here, that's why I told you to try with static ip address, the less features from the router you use (like dhcp) the better
If only the power LED glows, I'm afraid you have a nice paperweight.
I don't think that configuring your network card as a "obtain IP address automatically" is going to work here, that's why I told you to try with static ip address, the less features from the router you use (like dhcp) the better
If only the power LED glows, I'm afraid you have a nice paperweight.
mann wrote
Even 30-30-30 Hard reset does'nt work at all.
Only power LED glows.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
0
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#6
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 2
Helpful: 2
Solutions: 0
Stories: 0
Registered: 2022-02-21
Re:ADSL Modem TD-W8951 ND V1 bricked while updating firmware
2022-02-21 23:53:15
Dear mtruchado, I just confirmed that the modem is able to communicate with the computer. (My modem model is TD-W8961ND V3.0) How do I set the binary mode by default and send the firmware again.
2
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
2
We appreciate your feedback. Feel free to let us know more. Log in to submit feedback.
#7
Options
- Copy Link
- Report Inappropriate Content
Thread Manage
Announcement Manage
Posts: 3
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
2012-12-29 18:17:56
Posts: 3
Helpful: 0
Solutions: 0
Stories: 0
Registered: 2012-12-29
Information
Helpful: 0
Views: 1722
Replies: 6
Voters 0
No one has voted for it yet.
Tags
Report Inappropriate Content
Transfer Module
New message