Home Network Community > Deco > Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
< Deco

Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
123

Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2019-10-29 18:50:25 - last edited 2021-06-10 03:53:45
Model: Deco M9 Plus  
Hardware Version: V1
Firmware Version: 1.3.0

Our Deco m9+ x4 network is distributed on a big area. The distance to one Deco unit is to big so we bought two cpe210 units. I think they are configured as Ap & Client now, the problem is that the far away Deco not will use the Ethernet connection wia the cpe210, instead it use wifi with to the nearest Deco but with poor coverage. How shall I configure the two cpe210 to solve that? Thx in advance!

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?-Solution
2021-06-10 03:53:19 - last edited 2021-06-10 03:53:45

Dear @JackBaxtech,

 

JackBaxtech wrote

hi, I'm wondering whether this was resolved? 

 

I would like to use Router > Deco M4 > CPE210 > CPE210 > Deco M4.

 

Is this possible?

 

Yes, it's possible. The official firmware has been released to fix the problem, please check the firmware download link below:

 
>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  2  
  2  
#24
Options
22 Reply
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2019-10-30 03:23:15

@GoranAhlberg 

 

Hello, what is the current network diagram? How do you connect them to each other? 

 

What is the model number of the CPE?

 

The CPE device can be used to connect two devices far from each other, while it is an outdoor device; the performance will be affected a lot once you put it inside. 

 

Besides, with computer connected to the client CPE, can you get internet? And what is the speed you can get from it? Please click here to verify its IP address and gateway obtained by your computer. 

 

Looking forward to your reply. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2019-10-30 21:14:28

@Kevin_Z thx Kevin, it's a remote site & the owner will be away for a while, will return to you when we can access the site.

  0  
  0  
#3
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2019-11-01 03:43:39

@GoranAhlberg 

 

Definitely sure. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#5
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2020-01-29 18:54:07 - last edited 2020-01-29 18:58:26

@Kevin_Z sorry for the delay, went to the site today, updated Deco M9+ and Cpe210 v3 units to latest firmware.

Yes a PC can connect to internet via the client Cpe210 with good 80 Mbps (100/10 Mps line from isp) and the same subnet 192.168.68 as the Deco mesh, but the Deco M9+ refuse to use the Cpe-link to join the mesh, tried different Deco - same result. Any suggestions?

  0  
  0  
#6
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2020-02-27 12:40:50 - last edited 2020-02-28 03:34:04

@GoranAhlberg 

 

Hi, 

The reason that your Deco m9 cannot connect to the Internet using the CPE210 as access point is that the decos use their own seperate 5ghz channel as backhaul to communicate with each other. As far as I know, only a deco can relay to another deco because of that. I don't know if you can create the backhaul via ethernet cable though. 

  1  
  1  
#7
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2020-02-27 15:05:21

@Smed75 thx Smed75 - will go for a ap-solution at the end of the Cpe-link, strange that Tp-link staff not know about that limitation...

  0  
  0  
#8
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2020-02-28 03:33:58

@GoranAhlberg 

 

Not exactly. The Deco M9 plus supports regular ethernet backhaul and the wifi backhaul. Including 2.4GHz and 5GHz-1. Besides, there is a 5GHz-2 which work for wifi backhaul only. 

 

For the current network diagram, the wireless backhaul is meaningless due to the distance is longer than the wifi coverage area of each unit. Instead, we use the ethernet backhaul to build up the network connection. 

 

Ans back to your case, we found that the CPE does not forward the corresponding packets while make you fail to access internet. But do not worry about that, this issue will be fixed with firmware upgrading. And you can provide the hardware version/firmware version and country version of the CPE210,  then we can offer you a beta firmware to solve it. 

Note: You can find the hardware and country version on the back of the actual device, the firmware can be found on the web UI.

 

May it help.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#9
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2020-02-28 08:26:40 - last edited 2020-02-28 08:32:09

@Kevin_Z thx for your answer! H/w version is: 3.0, s/w version is: CPE210(EU)_3.0-up-ver2-2-1-P1[20190620-rel61499] & country is: Sweden
We would appreciate a lot if we could get access to a beta software that could solve the problem!

Regards
Göran


 
  0  
  0  
#10
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2020-02-28 11:29:56

@GoranAhlberg 

 

Hello Göran, thanks for your reply. 

 

We have submitted the application.  while considering there is no beta firmware for CPE210 EU V3 yet, we need take some time to release a new one to solve your problem. 

 

We kindly ask your understanding and patience. Any updates, we will let you know immediately. 

 

Thanks a lot. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#11
Options
Re:Need to extend a Deco m9+ mesh with cpe210 antennas, correct cpe210 config?
2020-03-09 01:53:12

@GoranAhlberg 

 

Hi, thanks for waiting. Our engineer sends it to you. Please check your inbox. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#12
Options
123

Information

Helpful: 0

Views: 6106

Replies: 22

Related Articles
Extend M9 mesh with M4 or M5??
1360 0
Extend Deco M9 to garden office
2387 0
 Extend Deco mesh outdoor
686 0
Need outdoor AP for my Deca M9 Plus mesh network
1002 0
 Deco M9 Plus and CPE210
632 0
 Need to extend Range
696 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.