Home

Forums

Stories

Knowledge Base

Home Network Community > Cable Modem&Routers > Archer CR1900 Wired Clients

< Cable Modem&Routers

Archer CR1900 Wired Clients

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer CR1900 Wired Clients

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ShosMeister

2019-10-06 16:49:20

Posts: 3

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2019-10-06

Archer CR1900 Wired Clients

2019-10-06 16:49:20

Model: Archer A10

Hardware Version: V1

Firmware Version: v1.0.0 Build 20170505 Rel547390

Had issues setting this up but think it's finally working well. Issue is that it shows 0 wired clients on the web page but there are 4 plugged in and - yes they all work?

What's up with that? Guessing it's just a browser/interface issue but would really like to be able to see all the devices that are connected. All the wireless clients show up just fine - it's just the wired ones.

Oh and BTW, there is no AC1900 or CR1900 available in the model pull-down.

Thanks!

3 Reply

Kevin_Z

2019-10-09 06:30:23

Posts: 21782

Helpful: 5155

Solutions: 2575

Stories: 21

Registered: 2018-12-24

Re:Archer CR1900 Wired Clients

2019-10-09 06:30:23

@ShosMeister

Hello, for the model number Archer CR1900, actually it is there already, once you type Archer CR1900 or CR1900 in the model number field, it will pop up the corresponding device automatically.

Back to your case; you can reboot the whole system and try to verify whether the wired clients show up.

Besides, please ensure that the IP addresses of these devices are obtained automatically, not static IP. And go to advanced-DHCP client list page to verify whether you can see them.

Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

ShosMeister

LV1

2019-10-20 20:16:46

Posts: 3

Helpful: 1

Solutions: 0

Stories: 0

Registered: 2019-10-06

Re:Archer CR1900 Wired Clients

2019-10-20 20:16:46

@Kevin_Z

I actually did verify there is at least one device that is getting a DHCP address from the CR1900. The others are probably static but that's very bad that they don't show up in the connected/client list don't you think?

Any way to correct this? Maybe there is a firmware update?

Thanks!!

Kevin_Z

2019-10-21 09:44:37

Posts: 21782

Helpful: 5155

Solutions: 2575

Stories: 21

Registered: 2018-12-24

Re:Archer CR1900 Wired Clients

2019-10-21 09:44:37

@ShosMeister

The web UI shows the online devices with dynamic IP, you can change the static IP back to dynamic IP to give it a go.

If you want to fix the IP address for certain device, you can use the address reservation to do so.

Good day.

Archer CR1900 Wired Clients

Archer CR1900 Wired Clients

Information

Voters 0

Tags