Home Network Community > Wi-Fi Routers > Archer C6 - WDS didn´t work on 5GHz
< Wi-Fi Routers

Archer C6 - WDS didn´t work on 5GHz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Archer C6 - WDS didn´t work on 5GHz

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer C6 - WDS didn´t work on 5GHz
Archer C6 - WDS didn´t work on 5GHz
2019-09-27 20:27:48 - last edited 2019-09-28 08:39:24
Model: Archer C6  
Hardware Version: V2
Firmware Version: 1.1.0

Hi Everyone,

 

I´m having an issue with my new Archer C6 router.

I´m trying to setup a WDS (bridge) to my main router (Huawei). If I set it up with a 2,4GHz it works well, ip adress is given to my computer, internet works well. As I need higher speed (500 Mbit optical connection), I´m trying to do the same on the 5GHz frequency. When I set it up (2,4GHz off), it gives me on the main page that WDS status "run", but I get no internet connection, even can´t ping my main router (but I get IP address with DHCP from the main router "192.168.0.1").

I´m not a professional, but have setup today also a new Archer C7 same way, to the same Huawei router (C7 for media room / C6 for living room bridge).

I´m running the latest available FW version for the C6 router. Is it possible that there is a FW issue with the 5GHz WDS function? Or I have a broken C6 router? Should I return it with warranty claim? (exchange it for another C6 / or it´s a known issue/bug?).

 

Thanks for any help in advance,

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Archer C6 - WDS didn´t work on 5GHz-Solution
2019-09-28 08:38:38 - last edited 2019-09-28 08:39:24

@Peter82 

 

Hi Everyone,

 

I was playing with the setting some hours and found the issue. Looks like the WDS type auto setting on the C6 is not working properly. After manual selection of WDS1 the  WDS bridge works good (even good speeds). Maybe something for Tp-link team to check for the next FW release (if there will be any in the future).

 

Recommended Solution
  6  
  6  
#2
Options
14 Reply
Re:Archer C6 - WDS didn´t work on 5GHz-Solution
2019-09-28 08:38:38 - last edited 2019-09-28 08:39:24

@Peter82 

 

Hi Everyone,

 

I was playing with the setting some hours and found the issue. Looks like the WDS type auto setting on the C6 is not working properly. After manual selection of WDS1 the  WDS bridge works good (even good speeds). Maybe something for Tp-link team to check for the next FW release (if there will be any in the future).

 

Recommended Solution
  6  
  6  
#2
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2019-09-29 05:46:05

@Peter82 

 

Hello, it is NOT a bug; the WDS mode reprents the different WDS categories, WDS 1 is the Three-Address Format, WDS 2 is Four-Rddress Format. 

 

For WDS bridge feature, the type is set as auto by default; in this way, it will send a packet of Four-Address to the root access point, once it detects it and replies, then they can communicate with each other via Four-Address, otherwise, they will change it to Three-Address.

 

Back to your case, it is more like that the root AP replies the Four-address related packets, while it does not support it actually, which result in the communication between the 2 devices down and failed to change to Three-address.


May it help and have a good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  2  
  2  
#3
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2019-09-29 19:01:02
Cambiar contraseña
  0  
  0  
#4
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2019-09-29 20:39:36

@Kevin_Z 

 

Hello. Thank you very much for the information, now I understand for what these mode selections are. I have at my hand some routers and done testing (the answer I get, that the Huawei rooter is answering wrong not stands, as my Archer C7 works well with it on the auto mode, so I´ve done some testing). All routers tested are running latest official FW. Tests done only on 5GHz (2.4GHz works well on C6).

 

HW on my hands:

Huawei HG8245U (my optical interface and main router to internet) (new)

TP-Link Archer C9 (media room) (4 yeras old, V1 HW)
TP-Link Archer C7 (work room) (new)

TP-Link Archer C6 (living room) (new)

D-Link DIR-882 (my secondary router connected with cable to the Huawei main router) (2 years old)

 

Used Huawei HG8245U to connect to, using auto mode, test results below:

TP-Link Archer C9 - Success

TP-Link Archer C7 - Success
TP-Link Archer C6 - Fail (only manual mode 1 works)

 

Used D-Link DIR-882 to connect to, using auto mode, test results below:

TP-Link Archer C9 - Success

TP-Link Archer C7 - Success
TP-Link Archer C6 - Fail (only manual mode 1 works)

 

From these test I assume, that something is wrong with the C6 router. I have not tested to do WDS inbetween TP-Link routers, as that´s not my usecase.

From my point of view, issue is solved (with using manual selection - WDS1).

 

Thanks once again for the explanation,

 

Have a nice day

 

  0  
  0  
#5
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2019-09-30 01:20:43

@Peter82 

 

Thanks for your reply and effort to do these tests. 

 

From the results, it seems that the Huawei router build up the wifi connection with C7/C9 automatically via three-address or four-address format. Not sure why the C6 failed when select auto mode, will try to do a test at our lab.

 

Besides, considering you have figured out the current issue, ,you can enjoy the internet with the devices. 

 

If need more help, just feel free to contact us.

 

Good day. 

 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2020-06-25 05:53:49

@Kevin_Z 

 

i bought a c6 today and presented the same problem.

 

 however, firmware does not have the option to choose wds mode manually.

 

 what can I do?

  0  
  0  
#7
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2020-09-29 19:04:10

@Ricardo_Lemos 

 

I'm facing the same problem, no WDS mode option. Have you found a solution?

 

Thanks!

  0  
  0  
#8
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2020-10-02 19:24:27 - last edited 2020-10-02 21:28:47

@Kevin_Z I have the same problem cant build up an 5ghz wds unless its channel 36, and even then it wont connect to the internet

  1  
  1  
#10
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2021-08-25 11:57:33 - last edited 2021-08-25 11:58:13

@JeffersonZanini 

 

The WDS mode is a hidden element in the screen. Not sure why they hide this selection in Archer C6 FW. 
 

Use your browser's dev tool and find the WDS mode element. Remove all the "hidden" properties and you can see the selections. 
 

and yes, my Archer C6 is also having issue bridging with my main Archer AX20 on Auto WDS mode. Changing it to WDS mode 1 solved it instantly. 
 

 

  1  
  1  
#12
Options
Re:Archer C6 - WDS didn´t work on 5GHz
2021-08-27 09:22:32

@johannlo 

 

Thank you for sharing the solution, and it's glad to hear you got it solved by changing the WDS mode on the Archer C6.

 

As replied earlier, the WDS mode represents the different WDS categories, WDS 1 is the Three-Address Format, WDS 2 is Four-Address Format. It is Auto by default, and it will try to connect to the main wireless by sending a packet of Four-Address first, if that fails, the C6 will try to connect to the main wireless via Three-Address.


If anyone still encounters the same issue, we would like to have the brand and model of the main router, then we will try to analyze why the C6 fails to connect to it. Thank you.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#13
Options
12

Information

Helpful: 0

Views: 12178

Replies: 14

Related Articles
Archer C6 - WDS does not work
2703 0
Archer C6 doesn't detect 5Ghz WDS mode
299 0
WDS not working on Archer c6
2556 0
Archer C6 v2: 5Ghz WDS Bridging Setup Grayed!
3737 0
Is WDS on Archer C6 compactible with that of C60
12409 0
ARCHER C6 [WDS] - Some sites not loading [FIXED]
672 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.