Home

Forums

Stories

Knowledge Base

Home Network Community > Deco > Buffering in house

< Deco

Buffering in house

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Buffering in house

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Buffering in house

Ned01

2019-08-29 10:56:59 - last edited 2019-09-02 01:12:01

Posts: 12

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2019-07-25

Buffering in house

2019-08-29 10:56:59 - last edited 2019-09-02 01:12:01

Model: Deco M5

Hardware Version:

Firmware Version: 1.3.1

I have three decos in mesh mode. I have a Samsung telly linked wifi to one of them (A - the one that is linked ethernet to my Virgin modem); I have a NAS (dlink) linked ethernet to another (C). If I play an mp4 file on my NAS on my telly I get buffering every couple of minutes watching the mp4 file. If I move my NAS to link to deco A, I don't get the buffering. But I want my NAS next to deco C for power source reasons. My decos are linked wifi A-B-C.

Can I use QoS to help this or is this restricted to internet access?

1 Accepted Solution

Ned01

LV1

2019-09-01 18:09:28 - last edited 2019-09-02 01:12:01

Posts: 12

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2019-07-25

Re:Buffering in house-Solution

2019-09-01 18:09:28 - last edited 2019-09-02 01:12:01

It seems to be sorted.

I've marked the NAS as 'high priority' and that sorted it. I did try also to mark the telly as 'high priority' as well but the result of that was that the telly lost contact with the NAS, which I don't understand.

I'm not sure if marking something as 'high priority' is the same as QoS.

Recommended Solution

4 Reply

Kevin_Z

2019-08-30 01:59:26

Posts: 21560

Helpful: 5021

Solutions: 2537

Stories: 21

Registered: 2018-12-24

Re:Buffering in house

2019-08-30 01:59:26

@Ned01

What is the current network diagram? Do the 3 Decos connect to each other by wireless? Like Virgin media modem--Main Deco A))))((( slave Deco B )))(((slave Deco C -- NAS?

Try to setup QoS to streaming and add them into high priority list to give it a go.

Still the same, please verify whether it works with TV connected to the Deco C.

Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Ned01

LV1

2019-09-01 15:06:47

Posts: 12

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2019-07-25

Re:Re:Buffering in house

2019-09-01 15:06:47

Thanks Kevin,

I will try that and I will also try using an ethernet cable as a part of the config.

You are right about my current config. I cannot link my telly to my node C without moving node C, but if the NAS is moved down to node A to which the telly is also linked there isn't a problem.

Ned01

LV1

2019-09-01 18:09:28 - last edited 2019-09-02 01:12:01

Posts: 12

Helpful: 2

Solutions: 1

Stories: 0

Registered: 2019-07-25

Re:Buffering in house-Solution

2019-09-01 18:09:28 - last edited 2019-09-02 01:12:01

It seems to be sorted.

I'm not sure if marking something as 'high priority' is the same as QoS.

Buffering in house

Buffering in house

Information

Voters 0

Tags