RE305 as access point
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.RE305 as access point
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi there,
i have some strange behaviour if i switch RE305 to access point. Once RE305 reboots, it is no more possible to contact the gateway from workstation or wifi clients.
If back to extender mode, no more problem, the gateway will be reach again.
What's wrong? Perhaps, i do not understand something?
Many Thanks,
Antonio
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Do you mean you cannot access the web UI of the RE305 when it works as access point ?
If so, below are some instructions to login:
1. With computer connected to the RE305, please open a web browser and enter tplinkrepeater.net to login; you can disconnect the RE305 and the main router first to login.
2. Or please login to the web UI of the main router to get the current IP address of the RE305, and use the IP to access the web UI of the extender.
May it help and have a nice day.
- Copy Link
- Report Inappropriate Content
Many thanks for your answer!
I'll try to better explain.
I have an ISP router, 192.168.1.1, with also Wifi AP.
If i configure RE305 as extender of ISP router WiFi, all is ok!
But two floor up, i prefer to setup RE305 as Access Point mode. So, from ISP router ui, i'll get RE305 IP, and then switch to Access Point Mode. As far as RE305 reboots, i'll lost the router, no ui, no ping 192.168.1.1. If i search RE305 IP, with Fast Resolver for example, i'll get to RE305 ui, but no more ISP router. It's very strange for me. Or is there something that i do not understand? From the manual, it seems very simple... switch to Access Point Mode, configure 2.4 and 5GHz, et voilà... well, it's true for RE305, but incredibly no more ping to ISP router!... and, obviously, no more internet as no more gateway...
Hope to explain well... if not, please ask me
Many thanks,
Antonio
- Copy Link
- Report Inappropriate Content
With 2 floors up, can you get internet with your computer connected to the main router directly by wired cable?
Please disconnect the main router and RE305 first, please reset the RE305 and configure it as an access point, instruction as below:
https://www.tp-link.com/support/faq/1401/
Once you changed it to access point mode, please connect it to the main router directly with ethernet cable and connect your client devices to the extender to verify whether you can access internet. Besides, please click here to check its IP address and default gateway.
Still the same, you can assign a static IP for thr RE305 under settings-network page and upgrade the firmware to the latest one.
May it work and have a nice day.
- Copy Link
- Report Inappropriate Content
Hi, I have the same problem !
RE305 in Access Point mode with standard configuration, block internet connection in all my network when connected to LAN.
Also when I assign a static IP address for it.
Scenario:
Router Fibra Vodafone Station with WiFi disabled (192.168.1.1)
No. 3 NOVA MW3 as Wifi Mesh repeater (DHCP client)
No. 1 TP-Link TL-WPA4220KIT with no.2 AV500 (DHCP client)
When I configure the RE305 as Access Point I cannot reach the Vodafone router and all clients stop to navigate on Internet.
The firmware is the latest one.
Does you know some incompatibilities with other extender?
Model: RE305(EU) Ver. 3.0 - firmware 1.0.1 Build 2019021 Rel 63495 (6985)
I found this post on Amazon Italia...
https://www.amazon.it/gp/customer-reviews/RP3R5IDN9KT7Q/ref=cm_cr_dp_d_rvw_ttl?ie=UTF8&ASIN=B01MD1SKLL
- Copy Link
- Report Inappropriate Content
Hello, could you please draw a picture of the current network diagram? How do you connect these devices together?
After you changed the RE305 to access point mode, have you connected it to the internet source by wired cable?
With computer connected to RE305, please click here to verify the IP and gateway obtained.
Good day.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@SimarInf Dear
I've the same issue and I'd want to know if you solved it (or not), just connecting the extender to the main router directly.
I'm facing the same issue with my RE305 set as AP: if it's connected to the router directly it's almost working fine (almost becasue it looses the signal sometime), but If i try to use it through a TP-LINK powerline (several types actually), It's not able to reach the router anymore. It seems it's not able to communicate with the router using a powerline (with the same brand, by the way). Does anybody else have experienced the same issue? if yes how does he handle it? Many thanks to whom will reply me.
- Copy Link
- Report Inappropriate Content
Hi.
I've just signed up as I'm searching for an answer to a similar problem, hoping someone can please help :)
I'm having similar issues to the guys above, in Access Point Mode the RE305 will only work if connected directly to the main router and not via a switch.
My Setup:
- Main Router (Viirgin Hub 3) feeds two TP-Link TL-SG105 switches, both switches have various devices connected
If I have the RE305 in Access Point mode, and connected to either of the switches ,not only will it will not connect to the network but it also causes all other devices connected to that switch to be disconnected from the same network. Devices connected to the other switch or directly to the router are fine.
If I connect the RE305 directly to the main router all is well......however this is not an option to have it permanently connected in this way as the main router is at the front of the house and naturally I bought an extender to provide coverage at the rear :)
I have tried various approaches over the last two days including assigning fixed IP addresses and nothing seems to fix it.
Is there a limitation of this device that will only allow it to work when connected directly to the router and not via a switch or powerline?
If so - is there another Access Point that will work when connected via a switch?
Thanks for any help :)
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Thanks Kevin and forgive me for my late response. I was able to make some new test and here the results. Using the Extender mode it works fine as you can see here:
Set it as Access Point it doesn't find the router and connect to the internet. WiFi is still working. Here the status:
On AP mode the led are as follows (with no signal at all):
Finally the device:
Finally I can confirm that attached to the router directly everything works properly also on AP mode.
Any help or suggestion will be really appreciated.
Thanks!
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 7836
Replies: 18
Voters 0
No one has voted for it yet.