Manually choose which Deco to connect

Manually choose which Deco to connect

Manually choose which Deco to connect
Manually choose which Deco to connect
2019-08-02 10:19:55 - last edited 2022-02-17 03:08:16
Model: Deco M5  
Hardware Version:
Firmware Version:

Hello everyone,

I have 9pieces of Deco M5 inside of a house. After a new firmware arrived, I checked the map of my Deco M5 (how they're connected to each other) and notices, that some Decos bypassed 1 or 2 decos on their way and connected to the main Deco through wi-fi. There are 1 or 2 Decos between them, but they decided to connect to the Deco (main) which is far away from them.

I wonder why they choose to connect to him, when closer Decos avaialble ? Also would be great, if we can manually choose which Deco to connect to what Deco.

Thanks

  11      
  11      
#1
Options
1 Accepted Solution
Re:Manually choose which Deco to connect-Solution
2022-02-17 03:08:10 - last edited 2022-02-17 03:08:16

  @mike78355957 

Hi, welcome to the community.

It is suggested to refer to this link and install the beta firmware to manually select the signal source on Deco M5.

Deco M5 1.6.0

Manual Signal Source Selection on Deco

Recommended Solution
  0  
  0  
#34
Options
43 Reply
Re:Manually choose which Deco to connect
2019-08-04 06:12:46

Also would be great, if web Deco names could be sync with names, that by was by mobile app, instead of custim_1, custim_2.....

  0  
  0  
#2
Options
Re:Re:Manually choose which Deco to connect
2019-08-05 07:27:42

@Boriy 

 

The Deco choose the front-end device to connect automatically, which cannot selected manually. While for the feature to choose the specific Deco to connect, we will note that and feed back.

 

For the device name issue, we have noticed that and reminded our R&d team; they are working on it. 

 

You can keep an eye on official website or Deco app for more updates. 

 

Best regards. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#3
Options
Re:Re:Re:Manually choose which Deco to connect
2019-08-08 06:44:18

Thank you for explanation @Kevin_Z 

Time by time Decos jumping from each other (connecting to different one). But we do not touch Deco and don't move them around. They have fixed place. I hope it can also be fixed.

  0  
  0  
#4
Options
Re:Re:Re:Re:Manually choose which Deco to connect
2019-08-08 09:47:56

@Boriy 

 

Thanks for your reply and clarification.

 

Per I said before, the  slave Deco choose the front-end device to connect automatically, which cannot selected manually now. While we have noted that and reminded our R&D team to plan to add the feature which can fix the front-end device in the next firmware. 

 

Best regards. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#5
Options
Re:Re:Re:Re:Re:Manually choose which Deco to connect
2019-08-08 19:27:07

@Kevin_Z 

Thanks for reply.


Also please, can we make it in real time ?

I believe it refresh every 10 seconds or so. Would be great to have it refreshing in real-time, so we can see actual speed

  0  
  0  
#6
Options
Re:Re:Re:Re:Re:Re:Manually choose which Deco to connect
2019-08-09 09:37:30

@Boriy 

 

I think it is more related to the browser settings. 

 

Theoretically, once you opened the web UI, it shows up the real-time rate. Without refreshing the browser, it may not change or delay.

 

Best regards. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#7
Options
Re:Re:Re:Re:Re:Re:Re:Manually choose which Deco to connect
2019-08-09 19:11:49

I tried in latest version of Safari & Chrome. It refresh every 7-8 seconds.

Would be great, to have it real-time. I think it's something, that most people would apprecaite it. 

  0  
  0  
#8
Options
Re:Re:Re:Re:Re:Re:Re:Re:Manually choose which Deco to connect
2019-08-13 02:10:59

Gotcha, have noted that. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#10
Options
Re:Re:Re:Re:Manually choose which Deco to connect
2020-05-13 07:15:49

@Kevin_Z 

 

Is there any update for the new firmware that enable us to MANUALLY choose the front end connection between deco. Its getting frustated here.

 

Best Regards,

Taufan

  7  
  7  
#11
Options
Re:Re:Re:Re:Manually choose which Deco to connect
2020-07-26 20:29:01
Gosh, it's been almost a year, can you believe it ? o_O Probably they forgot about it
  6  
  6  
#12
Options