Home Network Community > Deco > incorrect offline state after M4 firmware update
< Deco

incorrect offline state after M4 firmware update

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

incorrect offline state after M4 firmware update

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
incorrect offline state after M4 firmware update
incorrect offline state after M4 firmware update
2019-07-24 16:55:15 - last edited 2019-07-24 17:33:57
Model: Deco M4  
Hardware Version: V1
Firmware Version: 1.1.0 20190620 Rel. 45372

After firmware update of my M4 , wifi camera is shown in offline state in deco app., but actually it is online, connected to one of the Decos and works properly. If click on it in app (in offline mode), I can see wifi connection to the Deco :). So what does it mean?

  0      
 
  0      
 
#1
Options
20 Reply
Re:incorrect offline state after M4 firmware update
2019-07-25 02:21:58

@RedRoger 

 

Try to reboot the Deco M4 and the wifi camera. Meanwhile, try to close and re-open the Deco app to give it a go. 

 

Any updates, please let us know. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Re:incorrect offline state after M4 firmware update
2019-07-25 03:20:52 - last edited 2019-07-25 03:21:42

Nothing has changed. Situation the same.

  0  
  0  
#3
Options
Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-25 10:11:30

@RedRoger 

 

From Pa attached, there is no IP address, may I know have you ever setup a static IP for the camera?

 

At that time, can you ping the camera from another device, like computer in the same network? 

 

And what is the model number of the camera? 

 

Thanks in advance. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-25 10:48:21 - last edited 2019-07-25 10:51:34

Everything is operational, except the fact that in DECO app it's shown as offline device )) Stream of the camera is OK, it is available from the home network as well as from the internet. Web-interface of the camera is available as well. Pings are OK. IP camera is CAMHI pcs 112.  And yes, it uses static IP.

  0  
  0  
#5
Options
Re:Re:Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-25 11:19:05

And another feature. While other wifi devices see one mesh network as it should be, this one sees three - per one for every DECO as I understand

  0  
  0  
#6
Options
Re:Re:Re:Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-26 07:27:28

@RedRoger 

 

Thanks for your reply. From the pic attached, the LAN IP of the wifi camera is 192.168.88.137, while the LAN IP of the Deco M4 is 192.168.68.1 by default.

 

Theoretically, if you have not changed the LAN IP of Deco M4, to make devices access each other, the static IP of the camera should be 192.168.68.x. 

 

So may I know what is the current network topology? What is the LAN IP of the Deco M4 now?

 

To do a comparison test, with a computer connected to the Deco M4, please click here to check its IP and gateway; then try to ping the IP of the camera and show us the ping results.

 

Please ensure that the static IP of camera is in the same subnet as the Deco M4 and then check whether it still shows offline. 

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#7
Options
Re:Re:Re:Re:Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-26 08:19:27 - last edited 2019-07-26 08:26:23

3  units of Deco m4 work in AP mode. Two of them are connected to the main router using eth line, last one is wifi extender. DHCP server is running on the main Mikrotik router. All users, (except ip cameras and NVR) including all three Decos get IP addresses from the main router via DHCP. On the picture there is an ip address of the Deco, to which problem ip camera is connected. All three decos have dinamic IP at the same network: 192.168.88.12; 192.168.88.19; 192.168.88.21. PC has 192.168.88.18

  0  
  0  
#8
Options
Re:Re:Re:Re:Re:Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-26 08:51:26

Miracle has happened. Everything is working now properly after changing IP address of the camera from manual to dhcp and back to manual. Something somewhere was rewritten and everything is correct now ))

  0  
  0  
#9
Options
Re:Re:Re:Re:Re:Re:Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-26 09:54:29

@RedRoger 

 

Glad to hear that it was resolved finally, thanks for your feedback.

 

It seems that the original static IP may have something wrong, which makes Deco detect the camera as offline device.

 

While cause it is working fine now, you can enjoy the internet with the Deco units. 

 

Good day. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#10
Options
Re:Re:Re:Re:Re:Re:Re:Re:Re:Re:incorrect offline state after M4 firmware update
2019-07-26 12:50:15

Nope ). After some time of being active, camera again is in inactive group. Still have a problem.

  0  
  0  
#11
Options
12

Information

Helpful: 0

Views: 4387

Replies: 20

Related Articles
Deco M4 firmware update
4067 0
Deco M4 is down after latest firmware update
1873 1
[Troubleshooting] Deco M4 update firmware problems
5951 0
WPA8631P unable to update firmware (incorrect files)
964 0
 Update Firmware Deco M4 V3(EU)
597 0
 Deco M4 and P9 offline
311 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.