Archer C6 2.4G band stops working, disable then enable restores
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Recently purchased Archer C6 Router running the latest firmware. On 4 occasions the 2.4G WiFi band has stopped working, devices can connect to it but get no network access. Disabling and enabling the 2.4G band on the admin interface restores the connectivity, the 5G band is not affected, a device connected to it is used to reset the 2.4G band.
I used the chat support service to discuss the issue and the suggestion was to change from automatic to a fixed channel for the 2.4G band, this appeared to resolve the issue but it has happened again today, a phone which only works on 2.4G was showing the WIFI as access denied.
is there anything else I can do to resolve this issue.
StuartP
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
@Kreco and @MushyPotato still got issue with 1.3.5 firmware?
- Copy Link
- Report Inappropriate Content
My home network consist of fiberwire modem as Internet input, then C6 as a main router. The network then is configured like that:
- one LAN cable goes to Xbox, second to TV, third to the other TP-link router upstairs,
- 3-4 WiFi users - mobile phones, tablets, laptops, etc.,
- RE200 (at 5GHz) in other room connected to PC using LAN cable.
IPv6 disabled.
txbf mu-mimo enabled
- Copy Link
- Report Inappropriate Content
@Kubas I try reinstall 1.3.5 and my 5ghz still got spiked and not stable. I don't know why..but now I'm going back to 1.3.6 beta for now..thanks for helping :D
- Copy Link
- Report Inappropriate Content
@alan5579 Well today 2.4GHz finaly crashed... It makes almost a week without crash (1.3.5) instead of couple of hours (1.3.4)... But still..
- Copy Link
- Report Inappropriate Content
So, yesterday 2.5ghz wifi crashed me again. I have 1.3.5 Build 20200630 rel.57406 firmware.
Koblich
- Copy Link
- Report Inappropriate Content
Hi all,
Mine is still running, but even when it runs 2 weeks it could crash.
From my findings it runs better with guestnetworks disabled.
Disable everything that you dont need.
Never had a crash with 2.4ghz guest disabled. Tested with 1.3.0, 1.3.4 and 1.3.5. With beta 1.3.6 it crashes two or more times a day...
But i think tplink has some sort of driver problems at the moment, many different routers have such problems.
- Copy Link
- Report Inappropriate Content
@Kevin_Z - Hey Kevin i am having the same issue on my archer A6 v2.0 2.4G, Can i use the same firmeware? My current firmware is 1.1.5 Build 20191112 rel.36515(5553). Please help me out.
- Copy Link
- Report Inappropriate Content
Hello,
You may go to the local TP-Link website to download the latest firmware for your Archer C6 and update it, then monitor the performance:
https://www.tp-link.com/support/download/archer-c6/#Firmware
Here is the guide to upgrade it:
https://www.tp-link.com/support/faq/2139/
May it helps.
- Copy Link
- Report Inappropriate Content
I bought an archer c6 before two days and it's on 1.0.1 firmware and is working just fine...I have fiber 110/5 and I get 110/5 when I am connected on wifi.
It does the job on a 90m2 apartament.
My question is do I have to upgrade to 1.3.5 as I see to many issues happening by others?
- Copy Link
- Report Inappropriate Content
@El_Ranchero You should wait for confirmation here that everything is ok. I shouldn't have updated mine.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 5
Views: 123421
Replies: 580
Voters 3
