Archer C6 2.4G band stops working, disable then enable restores

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
191011...

Archer C6 2.4G band stops working, disable then enable restores

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
580 Reply
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-14 16:32:07 - last edited 2020-07-14 17:24:43

@aTOMic1971 

I am testing 1.3.5 at the moment. I will report as soon as possible.

 

Archer C6 V2 EU (Firmware: 1.3.7 Build 20200723 rel.33309(4555))
  0  
  0  
#94
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-14 16:52:18

@aTOMic1971 

 

Good summary.  Just for the purposes of this now very long thread....

 

I am not sure that this issue has even been officially acknowleged by TP-Link.

My experience to date has been that the F/W updates are suggested just to keep us occupied - there is no mention in the release notes that this issue is being addressed in the update.

  0  
  0  
#95
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-14 17:43:15

@DWR65 Does tplink read the forums? crying

  0  
  0  
#96
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-14 22:17:04

@Kubas 12 hrs at 1.3.5 without any problems with 2.4GHz connection... Lets hope it stays like that :) I will report tomorrow.

  0  
  0  
#97
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-15 08:08:40

@Kubas Is 1.3.5 ok? Has solved 2'4 problems?

  0  
  0  
#98
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-15 08:12:18 - last edited 2020-07-15 18:57:01

@adios 

24h on 1.3.5 without any problems so far. Looking good so far.

Archer C6 V2 EU (Firmware: 1.3.7 Build 20200723 rel.33309(4555))
  1  
  1  
#99
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-15 10:50:49

@StuartP Has just installed 1.3.5, and can't use 5GHZ 40 mhz. Always use 80 mhz, and one of my devices uses 5ghz, but only with 20/40 channel width. crying

 

Please solve this problem. I need to fix width in 40mhz.

  0  
  0  
#100
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-15 13:26:12

@adios 

Hi,

Is your 5g configured a/n/ac ?

Have no problem with a 5g 40mhz device. Most of my devices using 80mhz.

Archer AX73(EU)V1 in Router Mode to use OneMesh with RE300 (used as AP only)
  0  
  0  
#101
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-15 14:44:54

@aTOMic1971 I have tried all combinations, and router always emits in 80mhz.

  0  
  0  
#102
Options
Re:Archer C6 2.4G band stops working, disable then enable restores
2020-07-15 15:28:52

@adios 

Mine runs actual with auto settings. Later i can try to set it to 40mhz fix and scan the wireless.

 

Maybe only a side effect. You can try to set it to factory default, and reconfigure it manual. 

Archer AX73(EU)V1 in Router Mode to use OneMesh with RE300 (used as AP only)
  0  
  0  
#103
Options