Home Network Community > Deco > Can't establysh connection to many chinese devices.
< Deco

Can't establysh connection to many chinese devices.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Can't establysh connection to many chinese devices.

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Can't establysh connection to many chinese devices.
Can't establysh connection to many chinese devices.
2019-07-09 13:09:15 - last edited 2019-07-10 05:47:45
Model: Deco M5  
Hardware Version: V2
Firmware Version: 1.2.8

Hi all!
Can't establysh connection to many chinese devices ( IP camera, LED streap with WiFi controller) purchased in China.
At the same time this devices can connect to router from another manufacturer with EU firmware, but can't connect to M5 with israeli firmware.
I was try any methods to connect, but without positive results...
Who can help me with this issue?
Thank you.

 

  0      
 
  0      
 
#1
Options
3 Reply
Re:Can't establysh connection to many chinese devices.
2019-07-10 15:47:18

@Apmucm 

 

Move them closer to the Deco, and then try to connect to the Deco network.

 

Meanwhile, try to use the instructions as below:

 

1. Try to disable 5GHz.

 

2. Disable fast roaming and setup QoS as standard.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  1  
  1  
#2
Options
Re:Re:Can't establysh connection to many chinese devices.
2019-07-13 17:12:05

Thank you for help.

After  fast roaming disabling,  the camera was connected. 

Now I think , how to enable fast roaming and still the camera connected...

  0  
  0  
#3
Options
Re:Re:Re:Can't establysh connection to many chinese devices.
2019-07-15 01:21:33

@Apmucm 

 

With camera connected to the Deco network, you can re-enable the fast roaming via Deco app to see whether it work. 

 

If the camera lost connection, try to reconnect to it as the guidance mentioned on fast roaming page. 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 1153

Replies: 3

Related Articles
How many devices can connect to M5
4321 0
How many devices can connection in AX90 at the same time?
1285 0
How many devices.
538 0
Instructions in Chinese
717 0
Can't set up connection alerts
5758 2
 Archer D5 unstable connection - too many devices...?
401 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.