Home

Forums

Stories

Knowledge Base

Home Network Community > Wi-Fi Routers > Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"

< Wi-Fi Routers

Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

XDavidT

2019-05-11 12:21:33 - last edited 2021-09-03 01:18:23

Posts: 8

Helpful: 22

Solutions: 0

Stories: 0

Registered: 2019-05-11

Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"

2019-05-11 12:21:33 - last edited 2021-09-03 01:18:23

Model: TL-WR841N

Hardware Version: V11

Firmware Version:

I have 2 routers of TP-LINK, the last one I bouthg, is Archer C2 (Main router), get IP from ISP, working great and all is good.

DHCP is between 192.168.0.100-255

My old router is TL-WR841N/TL-WR841ND V11 (firmware was upgrade to the last one from official site).

Now, My main router (192.168.0.1) is connect to my old router that I need to be my access point.

I saw that old router made his LAN, and using 192.168.1.1 as DG, and DHCP between 192.168.1.100-255

The IP he got from main router is 192.168.0.143, so as the guide video say's, I try to change LAN IP to 192.168.0.2, but I get massage say: "WAN ip and LAN ip are in the same subnet".

Then unpluged the WAN from my network and connect only with my PC to the router, and it's work, but after I recconect the router to network ( this time to LAN port ), I can't reach out to the internet.

What did I do wrong ?

1 Accepted Solution

Kevin_Z

2019-05-13 02:14:08 - last edited 2021-09-03 01:18:16

Posts: 21755

Helpful: 5136

Solutions: 2565

Stories: 21

Registered: 2018-12-24

Re:Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"-Solution

2019-05-13 02:14:08 - last edited 2021-09-03 01:18:16

Hi,

Below is the instruction to configure the router as an access point.

https://www.tp-link.com/en/support/download/tl-wr841n/#video

In short, you need change the IP address to the same subnet first with computer connected to the router only, and then you need disable the DHCP server otherwise it will work as a router, not an access point. Then you can connect the main router to one of the LAN ports to get internet.

May it help and have a nice day.

XDavidT wrote

I have 2 routers of TP-LINK, the last one I bouthg, is Archer C2 (Main router), get IP from ISP, working great and all is good.

DHCP is between 192.168.0.100-255

My old router is TL-WR841N/TL-WR841ND V11 (firmware was upgrade to the last one from official site).

Now, My main router (192.168.0.1) is connect to my old router that I need to be my access point.

I saw that old router made his LAN, and using 192.168.1.1 as DG, and DHCP between 192.168.1.100-255

The IP he got from main router is 192.168.0.143, so as the guide video say's, I try to change LAN IP to 192.168.0.2, but I get massage say: "WAN ip and LAN ip are in the same subnet".

Then unpluged the WAN from my network and connect only with my PC to the router, and it's work, but after I recconect the router to network ( this time to LAN port ), I can't reach out to the internet.

What did I do wrong ?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

Recommended Solution

1 Reply

Kevin_Z

2019-05-13 02:14:08 - last edited 2021-09-03 01:18:16

Posts: 21755

Helpful: 5136

Solutions: 2565

Stories: 21

Registered: 2018-12-24

Re:Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"-Solution

2019-05-13 02:14:08 - last edited 2021-09-03 01:18:16

Hi,

Below is the instruction to configure the router as an access point.

https://www.tp-link.com/en/support/download/tl-wr841n/#video

May it help and have a nice day.

XDavidT wrote

I have 2 routers of TP-LINK, the last one I bouthg, is Archer C2 (Main router), get IP from ISP, working great and all is good.

DHCP is between 192.168.0.100-255

My old router is TL-WR841N/TL-WR841ND V11 (firmware was upgrade to the last one from official site).

Now, My main router (192.168.0.1) is connect to my old router that I need to be my access point.

I saw that old router made his LAN, and using 192.168.1.1 as DG, and DHCP between 192.168.1.100-255

The IP he got from main router is 192.168.0.143, so as the guide video say's, I try to change LAN IP to 192.168.0.2, but I get massage say: "WAN ip and LAN ip are in the same subnet".

Then unpluged the WAN from my network and connect only with my PC to the router, and it's work, but after I recconect the router to network ( this time to LAN port ), I can't reach out to the internet.

What did I do wrong ?

Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"

Can't use my router as access point - getting error "WAN ip and LAN ip are in the same subnet"

Information

Voters 0

Tags